DSC MAXSYS PC4020 Manual de instalación descargar pdf (Pagina 31)

Section 10: System Programming

SECTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

10.4Event Messages

The following event messages can be modified from

their default settings to suit the user’s needs. To enter

new labels, enter each character as outlined in “Program-

ming System Labels” on page 14.

These messages will only appear if the [*][6] “Special

Messages” toggle option is enabled by the end user/sys-

tem administrator.

The zone tamper and zone fault messages will be displayed

regardless of the [*][6] Special Messages option setting.

FAIL TO ARM

Ref #: [000100]

This message will appear on every keypad on a partition

when a valid code is entered but the partition is not

ready to arm. The message will clear after five seconds.

ALARM WHEN ARMED

Ref #: [000101]

This message appears when a partition is disarmed after

an alarm has occurred. The message will be displayed on

all keypads on the partition. The message will clear after

five seconds and display the zone(s) that went into alarm.

4701 2-W SMOKE

Ref #: [000102]

This is the zone label for the 2-wire smoke zone on the

PC4701 fire module.

4701 WATERFLOW

Ref #: [000103]

This is the zone label for the waterflow zone on the

PC4701 fire module

NOTE: If there is more than one of these fire mes-

sages to be displayed at once, the messages will scroll

one after another. Once any fire alarm has been

silenced a message “Fire Bell Has Been Silenced” will

be displayed on the partition and global keypads until

the partition is armed.

ZONE TAMPER

Ref #: [000104]

This message will appear on every partition keypad when

a zone using Double EOL supervision exhibits a tamper.

The message is displayed while viewing open zones.

ZONE FAULT

Ref #: [000105]

This message will appear on every partition keypad

when a zone fault occurs. The message is displayed

while viewing open zones.

10.5Swinger Shutdown

The swinger shutdown feature is designed to prevent a

runaway communicator from tying up the central station.

Each zone can be programmed to follow, or not follow, the

swinger shutdown programming (see section 5.4 “Zone

Programming - Zone Attributes”). There are two pro-

gramming items related to this feature: the Swinger Limit

and the Shutdown 24Hrs communicator toggle option.

Swinger Limit

Ref #: [00040201]

Enter the number of alarms/tampers/faults the panel

will communicate per zone before communications for

that zone shut down. Valid entries are from 000 to 255.

The default setting of swinger shutdown is 003. Entering

000 in this section will disable swinger shutdown.

Swinger Shutdown Reset Every 24 Hours

Ref #: [000401]

Scroll to the Shutdown 24Hrs option. If the Shutdown

24Hrs toggle option is enabled, the swinger shutdown

counter will be reset every day at midnight, or when the

partition is armed. The swinger shutdown counters keep

track of how many alarms have occurred on each zone,

shutting them down if they reach their limit. If disabled,

the swinger shutdown counters will only be reset when the

partition is armed. All zone tamper and zone fault swinger

shutdown counters are reset on arming. (Default = No)

10.6Tampers

Ref #: [000200]

The following system toggle options determine how the

panel will interpret zone tamper conditions. Press [*] to

toggle each option on or off.

• Tamper Inhibit: If enabled, a tampered zone will

always show as open. When this occurs, the user can-

not bypass the zone and arm the system until the

installer’s mode is entered. The message “Arming

Inhibited. Call for Service” will be displayed.

• If disabled, the tamper event will be transmitted but

the zone can be bypassed and the system armed.

(Default = No)

• Device Tmp Dis: If enabled, tampering of wireless

zones will always cause tamper alarms and transmis-

sions whether the system is armed or disarmed. If dis-

abled, wireless zone tampers will create a trouble

condition when the system is disarmed. The zone

tamper will be logged to the event buffer but no

Tamper alarm transmission will occur. The event is

only logged and transmitted when the partition is

armed. (Default = Yes)

• Tmp/Flt Opn Zn: If enabled, an armed zone of any

type that is tampered or faulted will generate an alarm

as well as the tamper or fault condition. If disabled,

tampers and faults will never cause an alarm condi-

tion. (Default = Yes)

10.7Telephone Line Supervision

Ref #: [000401]

Scroll to the TLM Enabled option. The panel will moni-

tor the presence of the telephone line and will indicate a

trouble condition if disconnected. If the TLM Enabled

option is selected, the system will test for telephone line

faults. The keypads will indicate any faults detected.

(Default = Yes)

If the TLM Aud Bell option is selected, the panel will

activate the burg bell outputs when the system is armed

with a TLM trouble present; the panel will indicate a

TLM trouble at the keypad when the system is disarmed.

If the option is disabled, only the keypads will annunci-

ate the trouble, whether the system is armed or dis-

armed. (Default = Yes)

The TLM Tbl Delay will control the number of tele-

phone line monitoring checks required before a tele-

phone line trouble is generated (Ref #: [00040206]). The

panel checks the telephone connection at 10-second

intervals. Valid entries are from 003 to 255 checks. The

default setting is 003.

1 2 ... 26 27 28 29 30 31 32 33 34 35 36 ... 51 52

Comentarios a estos manuales

Sin comentarios

DSC MAXSYS PC4020 Manual de instalación Pagina 31

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC MAXSYS PC4020