DSC PC2525 Manual de instalación

INSTALLATIONMANUALPC2525Version 1.1

6DisarmingEnter the premises through the designated entry-exit door. The keypad sounder will be on as a reminder todisarm the system. Go to the keyp

7Trouble Conditions[∗∗∗∗∗]+[2]The PC2525 continuously monitors a number of trouble conditions. If one of these conditions occurs, the keypad“Trouble”

8User Programming Commands[∗∗∗∗∗]+[5]+[Master Code]The [∗][5] programming command allows the user to program Access Codes 2 through 8; the First Acces

9Setting the Clock[∗∗∗∗∗]+[6]+[Master Code]+[1]The System Clock is a 24-hour clock. Hours and minutes must be entered as 2-digit numbers.• HH, hours:

10Utility Output Command[∗∗∗∗∗]+[7] or [∗∗∗∗∗]+[7]+[Access Code]The Programmable Output (PGM terminal) can be programmed for activation by a keypad co

11PROGRAMMINGIntroductionThe PC2525 is fully keypad-programmable, and also supports downloading programming functions. Thesystem’s EEPROM memory can

12SYSTEM PROGRAMMING SECTIONS[00] Binary ProgrammingThis section is normally used upon instruction from factory technical personnel for specialized pr

13To restore the smoke detectors to normal, clear all products of combustion from the detectors and performa reset by pressing the [∗] then [7] keys.

14[06] Programmable Output OptionsThe PGM terminal can be programmed to operate in response to various system operations. The output pulseconnects th

15[07] Keypad Lockout OptionsThis section determines how the Keypad Lockout function operates. The first number determines how manyinvalid Access Cod

16[09] Second System Option CodeZone Light 1: One Time Use Code OptionON: One Time Use Code Enabled. Access Code 8 may be used to disarm and then lat

17[10] Third System Option CodeZone Light 1: 2-minute Keypad Time-out Enabled / DisabledON: 2-minute Keypad Time-out Enabled. If no keys are pressed

18[11] Fourth System Option CodeZone Light 1: Bell Pulse OptionsON: Bell Pulses for All Alarms. The bell or siren will pulse for all types of audible

19COMMUNICATIONS PROGRAMMING SECTIONS[30] First Telephone NumberThis is the first telephone number the Communicator will dial. After entering Section

20[35] Restoral Reporting Codes, Zones 1 - 8These reporting codes are used by the communicator to transmit zone restorals for zones 1 through 8. Prog

21[42] Communication VariablesEnter four 2-digit numbers in this section; do not press the [#] key while entering data.Swinger Shutdown (number of tra

223 All other non-alarm reporting codes must be set up to send an extended 2nd round. The 1st digit of thereporting code is used to identify the even

23[46] First Communicator Option CodeZone Light 1: Communicator Disabled / EnabledON: Communicator Disabled. The system’s communicator will be shut o

24Zone Light 8 Closing Confirmation Enabled / DisabledON: Closing Confirmation Enabled. When an Access Code is entered to arm the system, the Exit De

25DOWNLOADING PROGRAMMING SECTIONS[70] First Downloading Option CodeZone Light 1: Downloading Answer Enabled / DisabledON: Downloading Answer Enabled.

41TABLE OF CONTENTSiFEATURES 1SPECIFICATIONS 1INSTALLATION 2Mounting the Panel ...

26LOCKOUT AND RESET SECTIONS[90] Installer Lockout EnableWhen this feature is enabled, performing a hardware or software reset to restore the system’s

27Customer _________________________________________________________________________________________Address __________________________________________

28PROGRAMMING WORKSHEETS[00] Binary Programming Page 12[01] Zone Definitions Page 12Default2 0 Zone 12 1 Zone 22 1 Zone 32 1 Zone 40 2 Zone 50

29PC2525 V1.1[07] Keypad Lockout Options Page 15Default0 0 Number of Invalid Codes before Lockout0 0 Lockout Duration (minutes)[08] First System O

30[12] Bypass Mask for Zones 1 - 8 Page 18DefaultON Zone Light 1ON Zone Light 2ON Zone Light 3ON Zone Light 4ON Zone Light 5ON Zone Light 6ON Zone

31PC2525 V1.1[35] Restoral Reporting Codes, Zones 1 - 8 Page 20I______I______I Zone 1 RestoralI______I______I Zone 2 RestoralI______I______I Zone

32[39] Maintenance Alarm Reporting Codes Page 20I_______I_______I Battery Trouble AlarmI_______I_______I AC Failure Trouble AlarmI_______I_______I

33PC2525 v1.1[45] Communicator Call Direction Page 22Default1 Zone Alarms and Restorals1 Access Code Openings and Closings1 Priority Alarms and Re

34PC2525 v1.1[74] Number of Rings Before Answering Page 25Default1 2 Valid entries are [01] to [12][75] Answering Machine Double-Call Timer Pa

2-Wire Smoke Detector Information:Zone Identifier: PFA1Type Zone: StandardLoop Style: Class B, Style BMaximum Line Resistance: 100Ω totalEnd of Line D

42ii[05] Second Master Code...

Digital Security Controls Ltd. warrants that for a period of twelve months from the date of purchase, the product shall befree of defect in materials

37

© 1995 Digital Security Controls Ltd.1645 Flint Road, Downsview, Ontario, Canada M3J 2J6Printed in Canada 29001634 R0

1Keypad ProgrammableThe PC2525 is complete with a default program sothat it is operational with a minimum of programming.The control panel is complete

2INSTALLATIONMounting the PanelSelect a dry location close to an unswitched AC source and close to the telephone line connection. Removethe control p

3Fire Zone WiringAny number of the 8 zones may be programmed as a Fire Zone; refer to Programming Section [01].Smoke detectors should be the latching

4Bedroom BedroomBedroomLiving RoomKitchenFamily RoomBedroomLivingRoomDiningRoomKitchenBedroomBedroomBedroom BedroomBasementLivingRoomDiningRoomNEVERHE

5KEYPAD FUNCTIONSIntroductionThe PC2550RK Keypad provides complete information and control of the PC2525 control panel. The panel canbe fully program