DSC Power432 PC585 Manual de instalación

InstallationManualWARNINGThis manual contains information on limitations regarding product use and function and information on the limitations as to l

6NOTE: This option can only be selected if Normally Closed (NC) detection devices or contacts are being used. NOTE: Only one NC contact can be conne

Getting Started: 2.11 Keypad Zones7Assigning Keypad ZonesWhen using keypad zone inputs, each input used must beassigned a zone number in Installer’s P

8Section 3: Keypad CommandsUse any system keypad to enter commands and/or programthe PC585 security system. The LED keypad uses functionand zone indic

Keypad Commands: 3.4 [*] Commands9[*][2] Trouble Display The panel constantly monitors itself for several different trou-ble conditions. If a trouble

10[*][5] Programming Access CodesThere are 37 access codes available to the user. They are:Access code (40) ... One master code Acce

Keypad Commands: 3.5 Function Keys11[*][7] Command Output FunctionsThe user can activate programmable output functions usingthe [*][7][1-2] commands.

123.6 Features Available for the LCD5500Z These features are only available for LCD5500Z keypads withzone inputs:Automatic Scrolling of Alarms in Memo

13Section 4: How to ProgramThe following section of the manual describes the Installer’sProgramming function and how to program the various sec-tions.

144.4 Programming Toggle Option SectionsSome programming sections contain several toggle options.The panel will use zone lights 1 through 8 to indicat

15Section 5: Program DescriptionsThe following section explains the operation of all programma-ble features and options and provides a summary of all

Limited WarrantyDigital Security Controls Ltd. warrants the original purchaser that for a period of twelve months fromthe date of purchase, the produc

16A violated Fire zone will be displayed on all keypads and canbe delayed at any keypad. Typically this zone is used forlatching smoke detectors.[08]

Program Descriptions: 5.4 Assigning Keypad Zones17NOTE: Any zone with the wireless attribute enabled will not cause an alarm for a fault condition wh

18NOTE: To use the Third Telephone Number, you must enable itin section [380], option [5], and program it in section [303].NOTE: Telephone numbers can

Program Descriptions: 5.9 Communicator – Reporting Formats19reporting code to the central station, if programmed. If thereis a closing or zone activi

201. If an event’s reporting code is programmed as [00] or [FF],the panel will not attempt to call central station.2. If the reporting code for an eve

Program Descriptions: 5.11 PGM Output Options21using the LINKS1000 with call back, you need to program theLINKS1000 Preamble with the downloading tele

22NOTE: If attribute [8] is turned ON, attributes [1-7] must also be turned ON.PGM Output Timer. . . . . . . . . . . . . . . . . . . . . . . Section [

Program Descriptions: 5.13 Bell23TLM Enable/Disable . . . . . . . . . . . . . . . . . . Section [015]: [7] TLM Trouble Beeps When Armed or TLM Audibl

24squawk the bell only when the system is away armed or dis-armed.The Opening After Alarm Keypad Ringback option willcause the keypad to beep 8 times

Program Descriptions: 5.20 Event Buffer255.20 Event BufferThe panel will store the last 128 events which occurred on thesystem. The Event Buffer will

iTable of ContentsSection 1: System Introduction 11.1 Specifications ...11.2 Add

26When used as a backup communicator, the panel will attemptto call the central station in the following manner:the panel will try to call using land

27Restore PC5132 to Default Programming . . . . Section [996]Restore PC5400 Printer to Default ProgrammingSection [997]Restore Panel to Default Prog

28Section 6: Programming WorksheetsFor the RecordCustomer: ___________________________________________________________________________________________

Programming Worksheets29Zone Programming SummaryZone programming can be found in sections [001] - [004], [101] - [132], [020] and [202] - [205]. Use

30Keypad Programming[000] Keypad Enrollment (Section 2.5 “Keypad Assignment”)NOTE: This must be done at each keypad requiring programming.[0] Slot

Programming Worksheets31NOTE: Zones 9-32 are only available for wireless zones.[002] Zone 9-16 Definitions (Section 5.2 “Zone Programming”)Default Def

32[012] Keypad Lockout Options (Section 5.21 “Keypad Lockout Options”)NOTE: If Keypad Lockout is active, the panel cannot be disarmed with a keyswitch

Programming Worksheets33[017] Fifth System Option CodeDefault Option ON Off Section ONI________I 1 WLS Key Does Not Use Access Codes* WLS Key Uses A

34Advanced System ProgrammingZone Attributes (Section 5.3 “Zone Attributes”)Zone Attribute Defaults (Y = Option ON; N = Option OFF):Section Zone # Zon

Programming Worksheets35[117] 17 ( ) I________I I________| I________| I________| I________| I________| I________| I________I[118] 18 (

iiPC585 Wiring Diagram

36[160] Maximum Dialing Attempts to Each Telephone Number (Section 5.5 “Communicator – Dialing”)Default: 008 I_______I_______I_______I Valid entries a

Programming Worksheets37Alarm Restoral Reporting Codes, Zones 1-32 (Section 5.8 “Communicator – Reporting Codes” & Appendix A)Section[324] Zone 1

38Closing (Arming) Reporting Codes, Access Codes 1-32 (Section 5.8 “Communicator – Reporting Codes” & Appendix A)Section[339] Code 1 Code 2 Code

Programming Worksheets39[352] Test Transmission Reporting Codes (Section 5.8 “Communicator – Reporting Codes” & Appendix A)I_______I_______I 1. P

40[370] Communication VariablesDefault Section003I_______I_______I_______I Swinger Shutdown (Alarms and Rest) (001-014 Transmissions, 000=disabled) 5.

Programming Worksheets41Downloading Options[401] First Downloading Option Code (Section 5.10 “Downloading”)Default Option ON OffOFF I_______I 1

42Module Programming[801] PC5400 Printer Module Programming Please refer to your PC5400 Installation Manual for installation and programming instructi

43 Appendix A: Reporting CodesThe following tables contain Contact ID and Automatic SIA for-mat reporting codes. For more information on reporting cod

44Table2: Contact ID Zone Alarm/Restoral Event Codes (as per ADEMCO):Program any of these codes for zone alarms/restorals when usingthe standard (non-

45 Appendix B: Programming KeypadsIf you have an LCD5500Z keypad, additional programming is required for proper operation. All LCD programming is done

1Section 1: System Introduction1.1 SpecificationsDownloading Software Support• PC585 v3.0 uses DLS 2002 and higherFlexible Zone Configuration• Four fu

46[60] First User Display MaskDefault Option ON OFFONI_______I 1 Hold [P]anic Keys prompt ON Hold [P]anic Keys prompt OFFONI_______I 2 Zone Bypassing

47[66] Keypad OptionsDefault Option ON OFFONI_______I 1 Display Access Code when Programming Display ‘X’ when ProgrammingONI_______I 2 Local Clo

48Programmable Labels Zone labels and other LCD display identifiers can be customized to make operation of the system easier for the end user. The fol

Programming Worksheets: 5.33 Daylight Savings Time49[075] Fourth User Display MaskDefault Option ON OFFONI_______I 1 User Initiated Call-up prompt

50Command Output LabelsDefault: “Command_O/P_1” - “Command_O/P_4”Program a label for each Command Output used, as it will appear at each partition.Sec

Programming Worksheets: 5.33 Daylight Savings Time51[997] View Software Version[998] Initiate Global Label BroadcastAll LCD programming is done per ke

©2002 Digital Security Controls Ltd.Toronto, Canada • www.dsc.comTechnical Support 1-800-387-3630Printed in Canada 29034576 R002Direct all comme

21.2 Additional DevicesIn addition to the information below, see the back cover for aDSC module compatibility table.PC5132 Wireless ReceiverThe PC5132

3Section 2: Getting StartedThe following sections provide a thorough description of howto wire and configure devices and zones.2.1 Installation StepsR

4Programmable Output Terminals – PGM1 and PGM2PGM1 can sink up to 50mA or300mA (depending on the PGMbuild option) of current. Connect thepositive sid

Getting Started: 2.5 Keypad Assignment52.5 Keypad AssignmentThere are eight available slots for keypads. LED keypads andthe LCD5501Z keypad by default