DSC Power432 PC585 Manual de instalación Pagina 26
- Pagina / 56
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
22
NOTE: If attribute [8] is turned ON, attributes [1-7] must also
be turned ON.
PGM Output Timer. . . . . . . . . . . . . . . . . . . . . . . Section [164]
[11] System Tamper (All Sources)
The PGM output will activate when any tamper condition is
present and will deactivate when all tampers are restored.
[12] TLM and Alarm
The PGM output activates when the system experiences both
a telephone line trouble and an alarm. When the system is
armed, the output will deactivate only if an access code is
entered or if the telephone line is restored.
If an alarm activates this output in the disarmed state, the out-
put will deactivate if a user enters a valid access code while
the Bell Cut-off timer is counting down, or if the telephone line
is restored. The output will also deactivate if someone arms
the system after the Bell Cut-off has expired.
NOTE: This output will activate for all silent and audible alarms
except the Duress alarm.
[13] Kissoff Output
The output will activate for two seconds after the control panel
receives the kissoff transmission from the central station.
[14] Ground Start Pulse
The PGM Output will activate for two seconds to obtain a dial
tone on Ground Start telephone equipment before the panel
attempts to dial. Insert two 2-second pauses at the beginning
of the telephone number when using this option.
[15] Remote Operation (DLS 2002 Support)
This output can be activated and deactivated remotely using
the DLS software.
[16] LINKS1000 Support (PGM1 Only)
The PGM output will be used as a data wire to communicate
telephone number information for the LINKS1000 cellular unit.
[17] Away Armed Status
When the system is armed in the Away mode, the PGM output
will activate at the beginning of the exit delay. The output
deactivates when the panel is disarmed.
[18] Stay Armed Status
When the system is armed in the Stay mode, the PGM output
will activate at the beginning of the exit delay. The output
deactivates when the panel is disarmed.
[19] [*][7][1] Command Output Option #1
[20] [*][7][2] Command Output Option #2
These outputs are user-initiated by entering [*][7][1-2] at any
keypad. When any output is activated, three acknowledgment
beeps are sounded.
NOTES on Option [20] [*][7][2]:
Press [*][7][2][Access Code, if required] to activate any out-
put programmed as one of PGM output option [03] or [20].
Traditionally, [*][7][2] has been reserved for resetting smoke
detectors. Smoke detectors should now be programmed as
output [03] “Sensor Reset”.
NOTE: Only ONE of options [03] Sensor Reset and [20]
[*][7][2] Command Output Option #2 may be programmed on
the same system.
[21]-[24] For future use
PGM Output Attributes
In addition to programming the output type, you must also
program the PGM output attributes for each output.
PGM output options [09] “System Trouble” and [10] “System
Event” have their own unique set of attributes listed below the
description of each output type.
PGM output options [01], [03], [05]-[08], [11]-[20] have the
following attributes:
Attribute ....ON OFF
[1] .......PGM Enable PGM Disable
[3] .......True Output Inverted Output
Attribute ON: the output energizes when activated
Attribute OFF: the output de-energizes when acti-
vated
[4] .......Output Pulsed Output ON/OFF
Attribute ON: the output will activate once for the
amount of time programmed in section [164]
when initiated by the user
Attribute OFF: the output will toggle ON or OFF
when initiated by the user.
(Only applicable to options [19]-[20].)
[5] .......Access Code Req. No code Req.
Attribute ON: the output requires a code for acti-
vation.
Attribute OFF: no code required.
(only applicable to keypad-activated outputs)
PGM attributes return to their default settings when you
change PGM output options. Please see the programming
worksheets for a list of the default settings for each PGM out-
put type.
Be careful when selecting the normal and active states of
each PGM output to ensure that an undesirable output state
does not occur after a loss and restore of AC power.
NOTE: Attribute [3] must be ON (default) for PGM output
option [16].
NOTE: If you program more than one PGM output as the
same output type (e.g. if PGM1 and PGM2 are both pro-
grammed as [19] Command Output 1), the settings for output
attributes [1], [2] and [5] must be the same. This does not apply
to outputs programmed as types [09] and [10].
PGM Output Attributes . . . . . . . . . . . . . . Section [141]-[142]
5.12 Telephone Line Monitor (TLM)
When the TLM Enable option is selected, the panel will super-
vise the telephone line and will indicate a trouble condition if
the telephone line is disconnected.
If the TLM Enable option is ON, the panel will check the tele-
phone line every 10 seconds. If the telephone line voltage is
below 3V for the number of checks programmed in the TLM
Trouble Delay section, the panel will report a TLM trouble.
The default number of checks is 3. Enter a number from [003]
to [255] in the TLM Trouble Delay section to change the num-
ber of checks before the TLM trouble is reported. Program-
ming a delay means that a momentary interruption of the
telephone line will not cause a trouble condition.
If the TLM Trouble Beeps When Armed option is enabled,
the panel will indicate a TLM trouble at the keypad while the
system is armed. To activate the bell output in the case of a
TLM trouble while the system is armed, the TLM Audible
(Bell) When Armed option must be selected.
When the trouble condition is restored, the panel can send a
TLM Restoral reporting code. Any events which occur while
the telephone line is down will also be communicated.
If the LINKS1000 Cellular Communicator, or LINKS2X50 is
being used, the panel can be programmed to report a TLM
Trouble Reporting Code.
- Installation 1
- Limited Warranty 2
- WARNING Please Read Carefully 2
- Table of Contents 3
- PC585 Wiring Diagram 4
- 1.1 Specifications 5
- 1.2 Additional Devices 6
- 1.3 Out of the Box 6
- Section 2: Getting Started 7
- 2.5 Keypad Assignment 9
- 2.6 Supervision 9
- 2.7 Removing Modules 9
- 2.8 Zone Wiring 9
- 2.9 Fire Zone Wiring 10
- 2.10 LINKS Zone Wiring 10
- 2.11 Keypad Zones 10
- Section 3: Keypad Commands 12
- 3.5 Function Keys 15
- Section 4: How to Program 17
- 4.5 Viewing Programming 18
- 5.2 Zone Programming 19
- 5.3 Zone Attributes 20
- 5.4 Assigning Keypad Zones 21
- 5.5 Communicator – Dialing 21
- 5.10 Downloading 24
- 5.11 PGM Output Options 25
- 5.13 Bell 27
- 5.14 Test Transmission 27
- 5.15 Transmission Delay 27
- 5.17 Arming/Disarming Options 27
- 5.18 Entry/Exit Delay Options 28
- 5.19 Swinger Shutdown 28
- 5.28 Clock Adjust 30
- 5.29 Timebase 30
- 5.31 Installer’s Lockout 31
- 5.32 Walk Test (Installer) 31
- 5.33 Daylight Savings Time 31
- For the Record 32
- Zone Programming Summary 33
- Keypad Programming 34
- Basic Programming 34
- Programming Worksheets 37
- Advanced System Programming 38
- Attribute: 39
- PGM Option 39
- Communicator Programming 40
- Downloading Options 45
- International Programming 45
- Module Programming 46
- Special Installer Functions 46
- Appendix A: Reporting Codes 47
- Codes (as per ADEMCO): 48
- Restoral 48
- ASCII Characters 51
- Changes for PC585 v3.0 56
- PC585 Module Compatibility 56
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC Power432 PC585
(16 paginas)
(12 paginas)
(32 paginas)AEG Electrolux HM604060MB manuales
Manuales del propietario y guías del usuario para No AEG Electrolux HM604060MB.
Ofrecemos 6 manuales en pdf AEG Electrolux HM604060MB para descargar gratis por tipos de documentos: Manual de usuario
Comentarios a estos manuales