DSC Power432 PC585 Manual de instalación Pagina 44
- Pagina / 56
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
40
[370] Communication Variables
Default Section
003
I_______I_______I_______I Swinger Shutdown (Alarms and Rest) (001-014 Transmissions, 000=disabled) 5.19
003 I_______I_______I_______I Swinger Shutdown (Tampers and Rest)(001-014 Transmissions, 000=disabled) 5.19
003
I_______I_______I_______I Swinger Shutdown (Maint and Rest) (001-014 Transmissions, 000=disabled) 5.19
000
I_______I_______I_______I Transmission Delay (001-255 seconds) 5.15
030 I_______I_______I_______I AC Failure Communication Delay (001-255 minutes) 5.8
003
I_______I_______I_______I TLM Trouble Delay (No. of checks required - valid entries 003 - 255) 5.12
030 I_______I_______I_______I Test Transmission Cycle (land line) (001-255 minutes/days)† 5.14
030 I_______I_______I_______I Test Transmission Cycle (LINKS) (001-255 days) 5.14
007
I_______I_______I_______I Zone Low Battery Transmission Delay (000-255 days) 5.8
030
I_______I_______I_______I Delinquency Transmission Cycle (000-255 days/hours) 5.8
†Depends on programming in section [702], option [3].
NOTE: To disable the AC failure communications delay, program [000].
[371] Test Transmission Time of Day
(Section 5.14 “Test Transmission”)
NOTE: If the land line test transmission cycle is programmed in minutes (section [702], option [3]), this section will not affect the
land line test transmission cycle.
Default
9999 I_______I_______I_______I_______I (Valid entries are 0000-2359, 9999 to disable)
[380] First Communicator Option Code
Default Option ON OFF Section
ON
I_______I 1 Communications Enabled Communications Disabled 5.5
OFF
I_______I 2 Restorals on Bell Time-out Restorals Follow Zones 5.8
OFF
I_______I 3 Pulse Dialing DTMF Dialing 5.5
ON
I_______I 4 Switch to Pulse Dialing on 5th Attempt DTMF Dial For All Attempts 5.5
OFF
I_______I 5 3rd Telephone Number enabled 3rd Telephone Number disabled 5.7
OFF
I_______I 6 Alternate Dial (1st and 3rd) Call 1st Number, Backup to 3rd 5.7
OFF
I_______I 7 Call LINKS as well as Land Line LINKS is Backup of Land Line(s) 5.26
OFF
I_______I 8 Delinquency Follows Zone Activity (Hours) Delinquency Follows Arming (Days) 5.8
[381] Second Communicator Option Code
Default Option ON OFF Section
OFF
I_______I 1 Open After Alarm Kypd Ringback enabled Open After Alrm Kypd Ringback disabled 5.17
OFF
I_______I 2 Open After Alarm Bell Ringback enabled Open After Alrm Bell Ringback disabled 5.17
OFF
I_______I 3 SIA Sends Programmed Rep. Codes SIA Sends Automatic Rep. Codes 5.9
OFF
I_______I 4 Closing Confirmation Enabled Closing Confirmation Disabled 5.17
OFF
I_______I 5-6 For future use —
ON
I_______I 7 Contact ID Uses Programmed Rep. Codes Contact ID Uses Automatic Rep. Codes 5.9
OFF
I_______I 8 For future use —
[390] LINKS Preamble (First Telephone Number)
(Section 5.26 “LINKS1000 Cellular Communicator”)
Default: FFFF I_______I_______I_______I_______I (Program all unused digits with Hex F)
[391] LINKS Preamble (Second Telephone Number)
(Section 5.26 “LINKS1000 Cellular Communicator”)
Default: FFFF I_______I_______I_______I_______I (Program all unused digits with Hex F)
[392] LINKS Preamble (Third Telephone Number)
(Section 5.26 “LINKS1000 Cellular Communicator”)
Default: FFFF I_______I_______I_______I_______I (Program all unused digits with Hex F)
[393] LINKS Special Function Preamble (All Telephone Numbers)
(Section 5.26 “LINKS1000 Cellular Communicator”)
Default: FFFFFF I_______I_______I_______I_______I_______I_______I (Program all unused digits with Hex F)
•Enter [*][2][*] (HEX B) to dial [*] • Enter [*][3][*] (HEX C) to dial [#]
- Installation 1
- Limited Warranty 2
- WARNING Please Read Carefully 2
- Table of Contents 3
- PC585 Wiring Diagram 4
- 1.1 Specifications 5
- 1.2 Additional Devices 6
- 1.3 Out of the Box 6
- Section 2: Getting Started 7
- 2.5 Keypad Assignment 9
- 2.6 Supervision 9
- 2.7 Removing Modules 9
- 2.8 Zone Wiring 9
- 2.9 Fire Zone Wiring 10
- 2.10 LINKS Zone Wiring 10
- 2.11 Keypad Zones 10
- Section 3: Keypad Commands 12
- 3.5 Function Keys 15
- Section 4: How to Program 17
- 4.5 Viewing Programming 18
- 5.2 Zone Programming 19
- 5.3 Zone Attributes 20
- 5.4 Assigning Keypad Zones 21
- 5.5 Communicator – Dialing 21
- 5.10 Downloading 24
- 5.11 PGM Output Options 25
- 5.13 Bell 27
- 5.14 Test Transmission 27
- 5.15 Transmission Delay 27
- 5.17 Arming/Disarming Options 27
- 5.18 Entry/Exit Delay Options 28
- 5.19 Swinger Shutdown 28
- 5.28 Clock Adjust 30
- 5.29 Timebase 30
- 5.31 Installer’s Lockout 31
- 5.32 Walk Test (Installer) 31
- 5.33 Daylight Savings Time 31
- For the Record 32
- Zone Programming Summary 33
- Keypad Programming 34
- Basic Programming 34
- Programming Worksheets 37
- Advanced System Programming 38
- Attribute: 39
- PGM Option 39
- Communicator Programming 40
- Downloading Options 45
- International Programming 45
- Module Programming 46
- Special Installer Functions 46
- Appendix A: Reporting Codes 47
- Codes (as per ADEMCO): 48
- Restoral 48
- ASCII Characters 51
- Changes for PC585 v3.0 56
- PC585 Module Compatibility 56
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC Power432 PC585
(16 paginas)
(12 paginas)
(32 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.127 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales