DSC Power608 Especificaciones Pagina 31
- Pagina / 52
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
31
P R O G R A M M I N G W O R K S H E E T S
[006] Installer’s Code (Section 4.1 “Installer Programming”)
Default: 5008 I_______I_______I_______I_______I
[007] Master Code (Section 5.1 “Programming Security Codes”)
Default: 1234 I_______I_______I_______I_______I
[008] Maintenance Code (Section 5.1 “Programming Security Codes”)
Default: AAAA I_______I_______I_______I_______I
[009] PGM Output Programming (PGM 1 and 2) (Section 5.11 “PGM Output Options”)
Programmable Output Options
01 Burglary and Fire Bell Output 13 Kissoff Output
02 For Future Use 14 Ground Start Pulse
03 Sensor Reset 15 Remote Operation (DLS-1 Support)
04 For Future Use 16 LINKS 1000 Support (PGM1 only)
05 System Armed Status 17 Away Armed Status
06 Ready To Arm 18 Stay Armed Status
07 Keypad Buzzer Follow Mode 19 Command Output #1 ([✱] [7] [1])
08 Courtesy Pulse 20 Command Output #2 ([✱] [7] [2])
09 System Trouble Output (with Trouble options) 21 Command Output #3 ([✱] [7] [3])
10 System Event [Strobe (with Event options)] 22 Command Output #4 ([✱] [7] [4])
11 System Tamper (all sources: zones, kpd, modules) 23 Silent 24 Hour (PGM2 Only)
12 TLM and Alarm 24 Audible 24 Hour (PGM2 Only)
Output types [03] and [20] cannot be used together on the same system.
Default Default
19
I_______I_______I PGM 1 10 I_______I_______I PGM 2
Program PGM Option Attributes in sections [141] & [142].
[010] PC5208 PGM Output Programming (PGM 3-10)
(Section 5.11 “PGM Output Options”)
Default Default
01
I_______I_______I PGM 3 01 I_______I_______I PGM 7
01
I_______I_______I PGM 4 01 I_______I_______I PGM 8
01
I_______I_______I PGM 5 01 I_______I_______I PGM 9
01
I_______I_______I PGM 6 01 I_______I_______I PGM 10
[011] PC5204 PGM Output Programming (PGM 11-14)
(Section 5.11 “PGM Output Options”)
Default Default
01
I_______I_______I PGM 11 01 I_______I_______I PGM 13
01
I_______I_______I PGM 12 01 I_______I_______I PGM 14
Program PGM Option Attributes in sections [141] - [154].
[012] Keypad Lockout Options
(Section 5.21 “Keypad Lockout Options”)
If Keypad Lockout is active, the panel cannot be disarmed with a keyswitch.
Default
000
I_______I_______I_______I Number of Invalid Codes Before Lockout (001-255 codes)
000
I_______I_______I_______I Lockout Duration (001-255 minutes)
[013] First System Option Code
Default Option ON OFF Section
OFF
I________I 1 Normally Closed Loops End-of-Line Resistors 2.8
OFF
I________I 2 Double End-of-Line Resistors Single End-of-Line Resistors 2.8
ON
I________I 3* Panel shows all troubles when armed Panel shows only Fire troubles when armed 3.4
OFF
I________I 4 Tampers/Faults do not show as open Tampers/Faults show as open 3.4
OFF
I________I 5 For Future Use
ON
I________I 6 Audible Exit Fault Enabled Audible Exit Fault Disabled 5.18
ON
I________I 7
Event Buffer Follows Swinger Shutdown Event Buffer Logs Events Past shutdown 5.20
OFF I________I 8 Temporal Three Fire Signal Enabled Standard Pulsed Fire Signal 5.13
* Option 3 must be OFF if LCD keypads older than v2.0 are used.
- System Introduction 1
- 1.2 Additional Devices 2
- 1.3 Out of the Box 2
- Getting Started 3
- Accessories 4
- 2.5 Keypad Assignment 5
- 2.6 Supervision 5
- 2.7 Removing Modules 5
- 2.8 Zone Wiring 5
- 2.9 Fire Zone Wiring 6
- 2.11 LINKS Zone Wiring 6
- 2.12 Keypad Zones 7
- Keypad Commands 8
- ✱] [6] menu. The keypad will 10
- ✱] to toggle 10
- 3.5 Function Keys 11
- KEYPADVCOMMANDS 12
- How to Program 13
- 4.5 Viewing Programming 14
- Program Descriptions 15
- 5.3 Zone Attributes 16
- 5.4 Assigning Keypad Zones 17
- 5.5 Communicator – Dialing 17
- 5.10 Downloading 20
- 5.11 PGM Output Options 21
- ✱] [7] [2]: 22
- 5.13 Siren 23
- 5.14 Test Transmission 23
- 5.18 Entry/Exit Delay Options 25
- 5.19 Swinger Shutdown 25
- 5.20 Event Buffer 25
- 5.21 Keypad Lockout Options 25
- 5.22 Keypad Blanking 25
- 5.23 Keypad Backlighting 26
- 5.24 Loop Response 26
- 5.25 Keypad Tampers 26
- Programming Worksheets 29
- (Section 2.12 “Keypad Zones”) 32
- Zone Definitions 35
- Zone Attributes 35
- Keypad Zone Assignments 35
- Module Programming 42
- Special Installer Functions 42
- Reporting Codes 43
- (as per ADEMCO): 44
- Programming LCD Keypads 45
- I_______I 5-8 For Future Use 47
- CHANGES FOR PC5008 v2.1 48
- Installation 49
- LIMITED WARRANTY 50
- WARNING Please Read Carefully 50
- Table of Contents 51
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC Power608
(8 paginas)
(12 paginas)
(32 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales