DSC PC255O Especificaciones

1SPECIFICATIONSControl Panel Specifications13 zones including:• 8 fully programmable supervised zones (EOL resistors)• Supervised fire zone• 1 auxilia

10automatically extended to include the day (two digits01...31), the month (two digits 01...12) and the year(two digits...e.g. 91, 92, 93...etc.)

11This output can be used for operating other devices suchas garage door opener, special lighting or door strikes.The programmable output must be sele

UL LISTEDCOMMERCIAL ANDRESIDENTIALINSTALLATIONS12The installation requirements listed below must be met forthe following grades of service.Grade ALoca

13PRINTER SETUPNote: Printer option has not been verified by UL.The PC2550 with version 1.0 or higher software iscapable of sending data to a local pr

14AbbreviationsEvent printouts are abbreviated. These are theabbreviations used:AC ACACC AccessALR AlarmTLM TLMAXSUP AUX SupplyBAT BatteryBELL BellCLS

15DOWNLOADINGThe PC2550 supports the DSC “downloading” package.See the downloading manual for details on specificcapabilities.There are several sectio

PROGRAMMINGGUIDE16IntroductionThe PC2550 is programmed by entering instructions fromthe panel keypad. The PC2550 memory is EEPROM andcan be reprogramm

17Enter [ ✱ 3 ✱ ] for a 4 second pause (Hex C)Enter [ ✱ 4 ✱ ] for additional dial tone search (Hex D)Enter [ ✱ 5 ✱ ] to dial a ‘#’ (Hex E)The total nu

18[07] Reporting Codes for Closing(Arming) via Access Codes 1 to 8The reporting codes in sections [07] to [10] are used toidentify “Openings and Closi

19• Auxiliary Power Supply Trouble• Periodic Test TransmissionNote: For UL residential installations, either AC failureor battery trouble reporting mu

2FEATURESKeypad ProgrammingThe PC2550 comes with a default program so it isoperational with a minimum of programming. It iscompletely programmable fro

20[1]*Light off= Communications are enabledLight on= Communications are disabled[2]*Light off = Restorals follow zonesLight on = Restorals sent on bel

21Notes: The maximum delays allowed for ULresidential installations are: Entry delay = 45 seconds;Exit delay = 60 seconds.The maximum delays allowed f

22EnterEnterEnterEnterEnter aaaaa newnewnewnewnew 44444 digitdigitdigitdigitdigit codecodecodecodecode ininininin eacheach

23Troubles (sections [12] and [13]) AAMisc Alarms (section [11]) (A1 to 99)Test Code (section [12]) 1C or DCSystem Test Code (section [10]) CCAfter Al

24[32] Group B Zone Assignment for Zones 1 to 8.[33] Group A Access Code Assignment for Codes 1 to 8.Note: Codes 9 to 16 are always assigned to Group

25[1]*Light off = 0 This section is used to set the numberLight on = 1 of rings that the panel must see before[2]*Light off = 0 it will answer a call

26JUST FOR THERECORDPC2550 Version 1.2Customer ___________________________________________________________________________________________Address ____

Note: In sections [01] through [13], do not enter any data in sections that are not used.[01] 1st Phone Number Page 16• Be sure to enter [#]

28PC2550 Version 1.2[09] Reporting Codes for Opening (Disarming) via Access Codes 1 to 8 Page 18Access Code 1 Access Code 5Access Code

29PC2550 Version 1.2[14] Zone Definitions for Zones 1 to 8 Page 19Notes: When defining zones, ASSIGN DELAY ZONES FIRST to zones 1, 2, 3...t

3INSTALLATIONBench TestingThe PC2550 contains a factory default program. Anyadditional programming required can be done throughthe keypad. For many ap

30PC2550 Version 1.2[17] 3rd System Option Code Page 20Default Zone Light On Zone Light Off OffZone Light 1 ... No bell d

31PC2550 Version 1.2[21] Auxiliary Delay Zone Times Page 21Default045Entry Time (in sec.)060Exit Time (in sec.)[22] Communication Variables

32PC2550 Version 1.2[29] Communicator Format Options Page 22Default 11st Telephone Number 12nd Telephone NumberEnter one HEX digit fr

33PC2550 Version 1.2[32] Zone Group B Assignment Page 23DefaultOn Zone Light 1OnZone Light 2On Zone Light 3On Zone Light 4OnZone Light 5On Z

34PC2550 Version 1.2Enter [0] for digit '0' in the phone number.[36] Software Reset EEPROM Memory to Factory Defaults Page 24[37]

35PC2550 Version 1.2Notes: IF ZONE LIGHT 5 IS ON AND ZONE LIGHT 4 IS OFF: Reporting codes programmed for telephone #1 will becommunicated to the monit

36LIMITED WARRANTYDigital Security Controls Ltd. warrants that for a period oftwelve months from the date of purchase, the productshall be free of def

HOOKUP DIAGRAM37NOTESSecurity detection devices that requirepower from the control panel must beUL listed for the intended applicationand operate over

38KEYPAD HOOKUP1. Each keypad has four colored leads: red (RED), black (BLK), yellow (YEL), and green (GRN). Connect the leads tothe corresponding ter

FCC COMPLIANCE STATEMENTCAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use th

4to supply AC power to the PC2550. The transformershould not be connected to an outlet that is controlled bya switch. If AC failure occurs it is displ

29000120 R11PC2550Notice of Software ReleasePC2550 software version 1.2 has now been released.This release adds support for the Escort Voice AssistedS

INSTALLATIONMANUALPC255OVersion 1.2This device complies with Parts 15 and 68 of the FCC rules. Operation is subject to thefollowing two conditions: (1

NOTES ON UL INSTALLATIONThis equipment is UL Listed in accordance with standard UL1023 (Household Burglar - AlarmSystem Units), standard UL985 (Househ

TABLE OF CONTENTSPageSpecifications ____________________________________________________________ 1Features ___________________________________________

Page[00] Binary Programming ____________________________________________________ 16[01] 1st Phone Number _____________________________________________

5panel. Connect all yellow wires from the keypads to the“YEL” terminal on the panel. Connect all red wires fromthe keypads to the “RED” terminal. Conn

6GUIDELINES FOR SMOKEDETECTOR LOCATIONExperience has shown that all hostile fires in family livingunits generate smoke to a greater or lesser extent.E

7KEYPAD FUNCTIONSIntroductionThe PC2550RK remote keypad provides completeinformation and control of the PC2550 control panel. Thepanel can be fully pr

8entered. Once the bypass command is entered, pressing[9] recalls the last zone or group of zones which wasbypassed. If the same group of zones is byp

9the [4] is released the system returns to the ready modeand the switched auxiliary supply is restored.User’s Programming Commands[✱]+[5]+[MASTER CODE