DSC PC5020 Manual de instalación descargar pdf (Pagina 34)

Programming Sections: 5.18 Event Buffer

For commercial applications Bell Squawk on Exit Delay may be

enabled. The panel will squawk the alarm output once every sec-

ond when the exit delay is initiated and 3 times a second for the

last 10 seconds until the exit delay expires.

Upon entry, if a Delay type zone is violated, the panel will begin

entry delay. The keypad will emit a steady tone. The keypad will

pulse the keypad sounder during the last 10 seconds to warn the

user the system is about to go into alarm. If there was an alarm

during the armed period, the keypad sounder will pulse for the

entire entry delay to warn the user of the previous alarm.

For commercial applications Bell Squawk on Entry Delay may

be enabled. The panel will squawk the alarm output once every

second until the entry delay expires or the system is disarmed.

This feature must not be used with 2 partitions.

NOTE:

Since two Delay zones are programmable, and there-

fore two different Entry Delays, when the panel is armed it

will use the Entry Delay for the first Delay zone violated.

If the Bell Squawk During Auto Arm option is enabled, the

bell will squawk while the system is auto-arming in order to

notify anyone on the premises that the system is being armed.

If Exit Delay Termination is enabled the panel will monitor the

Delay zones during exit delay. If a Delay type zone is violated then

secured during the exit delay, the exit delay will be terminated

and the panel will be armed immediately.

To prevent false alarms, use the built-in feature Audible Exit

Fault. If a delay type zone is violated within 4 seconds after the

exit delay has expired, the panel will sound the entry delay warn-

ing through the keypad and siren alerting the customer that an

improper exit was made. If the panel is disarmed within the entry

delay no signal is sent. If not, the panel will continue to sound

the alarm and send a signal to central station. This feature can be

disabled in Section [013] Option [6].

Bell Squawk During Auto Arm . . . . . . Section [014], Option [2]

Bell Squawk on Exit Delay . . . . . . . . . Section [014], Option [3]

Bell Squawk on Entry Delay . . . . . . . . Section [014], Option [4]

Audible Exit Delay . . . . . . . . . . . . . . . Section [014], Option [6]

Audible Exit Fault. . . . . . . . . . . . . . . . Section [013], Option [6]

Exit Delay Termination . . . . . . . . . . . . Section [014], Option [7]

5.18 Event Buffer

The panel will store the last 256 events that have occurred on the

system. Each event will contain the time, date, partition and the

event itself along with the zone number, access code number or

any other information pertaining to the event.

If the Event Buffer Follows Swinger Shutdown feature is

enabled the event buffer will not store events after the swinger

shutdown level has been reached. This will prevent the panel

from overwriting the entire buffer if a problem exists (see section

5.19

“Swinger Shutdown”

on page 31).

The event buffer can be viewed three different ways. It can be

viewed through an LCD keypad, printed on-site using the

PC5400 printer module or it can be uploaded through the DLS

software.

Viewing the Event Buffer

The following is the procedure for viewing the event buffer

through the LCD keypad:

Step 1 - Enter [*] [6] [Master Code]

Step 2 - Select ‘View Event Buffer’

The keypad will display the Event Number, Partition, Time and

Date of the event in question. Use the [*] key to toggle between

this information and the event itself. Use the arrow keys (<>) to

scroll through the events in the buffer.

When you have finished viewing the event buffer press the [#]

key to exit.

NOTE:

When viewing events for partitions 3 to 8 on an

LCD5500 v2.x and lower keypad, they will show as being

logged in the “System Area”.

Event Buffer Follows Swinger ShutdownSection [013], Option [7]

5.19 Swinger Shutdown

The swinger shutdown feature is designed to prevent a runaway

communicator from tying up the central station. Different limits

can be programmed for Zone Alarms, Zone Tampers and

Maintenance signals. After the panel has communicated the

programmed number of transmissions for an event it will no

longer report that event until the swinger shutdown is reset.

For example, the swinger shutdown limit for Zone Alarms is set

to [003]. The panel will not send more than 3 alarm signals for

each zone with a swinger attribute until the swinger shutdown is

reset.

The Bell output will not be activated for alarms on zones that

have exceeded the limit of alarms set in the Swinger Shutdown

counter.

Swinger shutdown on global zones will log once to the System

Area.

Swinger Shutdown will be reset on all partitions when any par-

tition on the system is armed, or every day at midnight. Once

reset, the panel will again communicate normally.

Swinger Shutdown Limit

(Alarms/Tampers/Maintenance) . . . . . . . . . . . . . . Section [377]

5.20 Keypad Options

The panel can be programmed to ‘lockout’ keypads if a series of

incorrect access code entries are made. After the Number of

Invalid Codes Before Lockout has been reached the panel will

lock out the keypad for the Lockout Duration and log the event

to the event buffer. For the duration of the lockout the panel will

sound an error tone when any key is pressed. The invalid code

counter will be reset every hour.

To disable Keypad Lockout program the Number of Invalid

Codes Before Lockout as (000).

NOTE:

If Keypad Lockout is active, the panel cannot be

armed or disarmed with a keyswitch.

If the Keypad Blanking Option is enabled the panel will turn

off all lights and LCDs on the keypads if no key is pressed for 30

seconds. The keys, however, will remain backlit.

The panel will turn the lights and LCDs back on if entry delay

begins or an audible alarm occurs. If the Code Required to

Restore Blanking Option is enabled, the lights and LCDs will

turn on when a valid access code is entered. Otherwise, the lights

and LCDs will turn on when a key is pressed.

NOTE:

Keypad function keys will still operate when the

keypad is blank, unless the function key is programmed to

require an access code.

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 42 43

Comentarios a estos manuales

Sin comentarios

DSC PC5020 Manual de instalación Pagina 34

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC PC5020