DSC PC6010 Manual de usuario descargar pdf (Pagina 14)

Section 4: Module Enrollment

4.4 Enrolling PC6108A, PC6204,

PC6216, PC6400, and PC6820

Modules

At any enrolled keypad:

1. Enter installer’s programming by pressing [*] [8] [Installer’s Code].

2. Scroll to “Module Hardware” and press the [*] key.

3. The keypad displays the message “Enroll Module”. Press the

[*] key.

4. Scroll through the module types until the module you wish to

enroll is displayed. Press the [*] key.

5. The keypad displays the message “Create Tamper On Desired

Unit”. To enroll the module, you will need to create a tamper

condition on it. To create the required tamper, secure the tamper

zone on the module, and then open the tamper zone. It is the

transition from secure to violated which enrolls the module.

6. After the module has been tampered, the keypad displays the

module number and confirms enrollment (e.g. “PC6204 Mod

01 Enrolled”).

Record the module number in the Programming Worksheets.

7. Once the module is enrolled, re-secure the tamper.

Enrolling Zone Expanders

NOTE: Enroll all zone expanders before assigning zones to

PC6820 modules.

Zones 001 to 016 are located on the main control panel.

Additional zones are added in sequence. For example, if you

enroll two PC6108A zone expanders, the first one will be

assigned zones 017 to 024, and the second will be assigned

zones 025 to 032.

The system can have a maximum of 256 zones. To confirm which

zones are assigned to which expander, press any key when the

keypad displays the enrollment confirmation message.

NOTE: Be sure to record the zones assigned to each zone

expander module in the System Overview section of the

Programming Worksheets.

4.5 Enrolling PC6442 and PC6443

Modules

Before you can enroll any PC644X module, you must program

the Originator ID to be [01]. After the Originator ID is changed

to [01], you will be able to access all of the Backbone

programming sections. See “Backbone Section” in the

Programming Manual, for more information. At any enrolled

keypad, do the following:

1. Enter installer’s programming by pressing [*] [8] [Installer’s Code].

2. Scroll to “Backbone Section” and press the [*] key.

3. Scroll to “Originator ID” and press the [*] key. Program [01] in

this section.

4. Press [*], then scroll to “Module Hardware” and press the [*] key.

5. Scroll to “Backbone Modules”. Press the [*] key.

6. The keypad displays the message “Enroll Module”. Press the

[*] key.

4.1 Enrolling Keypads and Modules

Once you have completed the wiring of all keypads and

modules, they must be enrolled on the system.

Apply power to the system by first connecting the battery,

followed by the AC transformer (see section 3.16). All LCD

keypads will display the message “PC6501 DSC Ltd.”

NOTE: Make sure all power to the system is OFF when connecting

any modules.

NOTE: Record the location and the number of each module in

the Programming Worksheets for future reference.

4.2 Enrolling the First Keypad

To enroll the first keypad, go to the keypad that is to be

assigned to area 1. Press any key on that keypad.

The keypad beeps and displays the message “65XX Mod. #1.”

This keypad is automatically enrolled and assigned to area 1.

Once you have enrolled the first keypad, you can enroll the rest

of the system keypads and modules through the “Module

Hardware” section of installer’s programming.

4.3 Enrolling All Other Keypads

At the keypad you have just enrolled:

1. Enter installer’s programming by pressing [*] [8] [Installer’s

Code].

NOTE: The default installer’s code is [5555].

2. Use the arrow keys (<>) to scroll to “Module Hardware”.

Press the [*] key.

3. The keypad displays the message “Enroll Module”. Press [*].

4. Scroll through the module types, until the PC6501 keypad is

displayed. Press the [*] key.

5. The keypad will display the message “Press Any Key On

Desired Unit.” Go to the keypad to be enrolled and press any

key.

6. Return to the original keypad. A message similar to the

following will confirm enrollment of the keypad:

“PC65XX Mod 02 Enrolled”

7. Next, you must select which area the keypad will control. Use

the arrow keys (< >) to scroll to the desired area. Press the [*]

key to select the area. If you press the [#] key, the keypad will

be assigned to Area 1 by default.

NOTE: To change the area to which a keypad is assigned, you

must delete, and then re-enroll the keypad.

8. Make sure you record the module number and assigned

areas of all keypads on the Programming Worksheets.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 27 28

Comentarios a estos manuales

Sin comentarios

DSC PC6010 Manual de usuario Pagina 14

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC PC6010