DSC PC6010 Manual de usuario descargar pdf (Pagina 23)

9.1 Programming the System Using

Downloading Software

Another way to program the PC6010 system is by using a

computer and DLS-3 downloading software. You can enter the

programming data in the computer, and then use a modem, or a

PC-LINK module to send the data to the control panel. You can

do this over the telephone line with a remote computer, or at a

computer located on site.

Please see the DLS-3 manual for complete instructions on how to

install, set up and use the DLS-3 software. See the DLS Section

of the PC6010 Programming Manual for information on DLS-3

programming options.

9.2 Downloading over Telephone Lines

Make sure the “TIP” and “RNG” terminals are connected to the

telephone line. Program the downloading access code and the

panel I.D. code in the PC6010. Make sure that these codes are

also programmed correctly in the DLS-3 account file.

You can also set up downloading using the LINKS1000 module

as either a primary or backup communicator. See the “LINKS

Module” section in the Programming Manual for more

information.

You can set up the downloading so that the PC6010 will call the

computer, or have the computer call the control panel.

To have the control panel answer the telephone line when the

computer calls, you must enable either the “Ring Detect” or the

“Usr Allows Srv” downloading toggle options.

If you enable the Ring Detect option, the control panel will

always answer incoming telephone calls.

If you turn on the “Usr Allows Srv” downloading toggle option,

a Master user will have to answer YES to “Allow System

Service?” for the control panel to answer the telephone line. The

control panel will answer the telephone line for 60 minutes.

Master users will also have to Allow System Service before

Installer’s Programming is available at a system keypad.

If you enable both Ring Detect and Usr Allows Srv, the panel will

always answer telephone calls, but a Master user will still have to

Allow System Service, before the DLS-3 user or an installer can

access Installer’s Programming.

Section 9: Downloading

You can program the number of times the telephone line will

ring before the control panel answers it in the “# of Rings”

section. The default setting is 8 rings.

See the PC6010 Programming Manual for a complete

description of DLS Programming options.

9.3 PC-LINK

The PC-LINK module allows a direct connection between an on-

site computer and the control panel. With the PC-LINK, the

computer can communicate with the panel at 9600 baud. Use a

serial cable to link the computer with the control panel.

To download using PC-LINK:

1. Connect the PC-LINK connector to

the header on the PC6010 board,

as shown.

2. Enable PC-LINK in the Modem

Configuration section of the DLS-3

software. The software will display “PC-LINK Active” in the

Status Bar of the Communications window.

3. Open the appropriate account in the DLS-3, and select the

function to be performed (upload, download, etc.)

4. Go to any system keypad and enter Installer’s Programming

and select “System”, then “DLS Section”, then “Enable PC-

LINK”. The keypad displays the message “PC-LINK Active (#)

To Exit”.

5. Once the DLS communication is in progress, the panel will

automatically exit the Installer’s Programming mode.

6. When the desired DLS function(s) are complete, press the

hang-up button on the Communications window. This will

disconnect the DLS from the panel.

7. When you are finished, remove the PC-LINK connector from

the PC6010.

WARNING: Failure to remove the PC-Link connector from

the PC6010 after upload/download is complete will prevent

the panel from communicating successfully with the

monitoring station.

1 2 ... 18 19 20 21 22 23 24 25 26 27 28

Comentarios a estos manuales

Sin comentarios

DSC PC6010 Manual de usuario Pagina 23

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC PC6010