
36
Section PGM Output 1 2 3 4 5 6 7 8
#Type*
Main Board
[141] 1 ( ) I________I I________| I________| I________| I________| I________| I________| I________I
[142] 2 ( ) I________I I________| I________| I________| I________| I________| I________| I________I
PC5208
[143] 3 ( )
I________I I________| I________| I________| I________| I________| I________| I________I
[144] 4 ( ) I________I I________| I________| I________| I________| I________| I________| I________I
[145] 5 ( ) I________I I________| I________| I________| I________| I________| I________| I________I
[146] 6 ( ) I________I I________| I________| I________| I________| I________| I________| I________I
[147] 7 ( ) I________I I________| I________| I________| I________| I________| I________| I________I
[148] 8 ( ) I________I I________| I________| I________| I________| I________| I________| I________I
[149] 9 ( ) I________I I________| I________| I________| I________| I________| I________| I________I
[150] 10 ( ) I________I I________| I________| I________| I________| I________| I________| I________I
PC5204
[151] 11 ( ) I________I I________| I________| I________| I________| I________| I________| I________I
[152] 12 ( ) I________I I________| I________| I________| I________| I________| I________| I________I
[153] 13 ( ) I________I I________| I________| I________| I________| I________| I________| I________I
[154] 14 ( ) I________I I________| I________| I________| I________| I________| I________| I________I
*Record here based on programming in [009], [010] and [011].
[160] Maximum Dialing Attempts to Each Telephone Number
(Section 5.5 “Communicator – Dialing” )
Default: 008 I_______I_______I_______I Valid entries are 001-015 attempts (do not enter 000).
[161] Post Dial Wait for Handshake (All Formats)
(Section 5.5 “Communicator – Dialing” )
Default: 040 I_______I_______I_______I Valid entries are 001-255 seconds
[164] PGM Output Timer
(Section 5.11 “PGM Output Options” )
Default: 005 I_______I_______I_______I Valid entries are 001-255 seconds
[202] Zone Assignments 01-08
(Section 5.2 “Zone Programming” )
Program zone definitions in sections [001] - [004] and zone attributes in sections [101] - [132]. Program keypad zone assignments
in section [020].
NOTE: Any zones not used on the system should be disabled
in this section. Disabled wireless zones should have a blank
serial number (i.e., [000000]).
Zones 1-8: Default = ON; Zones 9-32: Default = OFF
Section Option: 1 2 3 4 5 6 7 8
[202] Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8
I______________I I______________I I______________I I______________I I______________I I______________I I______________I I______________I
[203] Zone 9 Zone 10 Zone 11 Zone 12 Zone 13 Zone 14 Zone 15 Zone 16
I______________I I______________I I______________I I______________I I______________I I______________I I______________I I______________I
[204] Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24
I______________I I______________I I______________I I______________I I______________I I______________I I______________I I______________I
[205] Zone 25 Zone 26 Zone 27 Zone 28 Zone 29 Zone 30 Zone 31 Zone 32
I______________I I______________I I______________I I______________I I______________I I______________I I______________I I______________I
Communicator Programming
NOTE: For sections [301] to [353], the content of every sec-
tion by default is [F].
Comentarios a estos manuales