DSC NT9005 V1.0 Especificaciones descargar pdf (Pagina 28)

20 24-Hr Freeze - Similar to 24-Hr Burglary except for Sys-

tem Event output type and SIA identifier.

21 24-Hr Latching/Tamper - If this zone is violated, the sys-

tem will not arm until [*][8][Installer’s Code] is entered.

22 Momentary Keyswitch Arm - Momentary violations of

this zone will alternately arm/disarm the system.

Do not use with wireless zones.

23 Maintained Key Switch Arm - When zone is violated,

the system will arm. When zone is secured, the system

will disarm.

NOTE: Do not use with wireless zones.

24 Future Use

25 Interior Delay - When the system is fully armed (i.e.,

Away Armed) this zone will follow exit delay. It will also

follow the entry delay, provided that the delay zone is

tripped first; otherwise it will go into alarm instantly.

When the system is Stay Armed, this zone will be active,

but when it is tripped, it will initiate the entry delay.

26 24-Hr Non-Alarm Zone - This zone does not sound a

bell, nor transmit any alarm condition to the central sta-

tion. Can be used to sound the door chime.

87 Delay 24-Hr Fire (Wireless) - Used only with wireless

smoke detectors.Delayed 24-Hr Fire (Wireless) works the

same way as the standard fire zone, except the alarm

memory and transmission by the communicator is

delayed by 30 seconds. If the alarm is acknowledged by

pressing any key within 30 seconds, the bells will silence

and the transmission will be aborted. After the alarm has

been acknowledged, and the smoke detector has not

been restored to normal, after 90 seconds the bell output

will be activated again; the user then has another 30 sec-

ond delay before the bell output latches and communica-

tions is activated. A code would then be required to

silence the bell output.

☞

The Fire Delay will be terminated if a 2nd fire zone is

tripped or if the [F] key is pressed during a delay.

88 Standard 24-Hr Fire (Wireless) - Used only with wire-

less smoke detectors. On alarm, the bell output will

sound to indicate that the fire loop has been activated. If

enabled, the communicator will immediately transmit the

alarm to the monitoring station.

☞

Do NOT change the default settings for Zone Attributes

on Fire type zones.

[001] - [004] Zone Definitions

FLASH

This section requires 32 two digit entries. Each two digit entry deter-

mines how the zone will operate. See Zone Definitions on the pre-

ceding page and Zone Attributes section [101]-[132].

Section Zone Default Zone Definition

[001] 01 01

I___I___I

02 03 I___I___I

03 03

I___I___I

04 03 I___I___I

05 04

I___I___I

06 04 I___I___I

07 04

I___I___I

08 88 I___I___I

[002] 09 00

I___I___I

10 00 I___I___I

11 00

I___I___I

12 00 I___I___I

13 00

I___I___I

14 00 I___I___I

15 00

I___I___I

16 00 I___I___I

[003] 17 00

I___I___I

18 00 I___I___I

19 00

I___I___I

20 00 I___I___I

21 00

I___I___I

22 00 I___I___I

23 00

I___I___I

24 00 I___I___I

[004] 25 00

I___I___I

26 00 I___I___I

27 00

I___I___I

28 00 I___I___I

29 00

I___I___I

30 00 I___I___I

31 00

I___I___I

32 00 I___I___I

When a valid [P] key alarm is generated, the keypad buzzer

and the bell output will remain silent, but the alarm will still

be transmitted (if programmed).

3 ON Quick Exit Enabled 

When armed, users may enter the [*][0] command to allow a

single Delay 1 or Delay 2 zone to be activated so they may

leave the premises. Only one Delay zone may be activated;

any additional activity on another Delay zone will cause its

respective alarm sequence. If the Delay zone is still open two

minutes after the [*][0] command is entered, the Entry Delay

will begin. If armed in the Stay mode, the automatic bypass

on Stay/Away zones will not be removed.

OFF Quick Exit Disabled 

4 ON Quick Arming Enabled/Function Keys Do

Not Require Code



[*][0] arming and Stay/Away function keys may be used to

arm the system without the entry of a valid access code.

OFF Quick Arming Disabled/Function Keys

Require Code



[*][0] arming is not permitted. All Arming keys require an

access code.

5 ON Code Required for Bypassing 

After entering the [*][1] Bypass Zones Command, an access

code must be entered before zones may be bypassed.

OFF No Code Required for Bypassing 

Enter the [*][1] Bypass Zones Command to bypass zones.

6 ON Master Code Not Changeable 

The Master Code (Access Code 40) may not be changed by

the user, and may only be programmed in the Installer’s Pro-

gramming mode.

OFF Master Code Changeable 

The Master Code (#40) may be programmed by the user

using the [*][5][Master Code] command. The Master Code

may also be programmed in section [007]

7 ON Telephone Line Monitor (TLM) Enabled 

The TLM function will be active and the system will indicate a

Trouble #3 condition when using the [*][2] View Trouble

Conditions Command.

OFF Telephone Line Monitor (TLM) Disabled 

The TLM function will be shut off and telephone line troubles

will not be indicated by the system.

8 ON TLM Audible when Armed 

When the system is disarmed, a telephone line monitor trou-

ble will generate a trouble indication as described above. If

the system is armed, a telephone line monitor trouble will

generate an audible alarm on the bell or siren for the dura-

tion of bell timeout or until an access code is entered.

OFF TLM Trouble Only when Armed 

A telephone line trouble will generate a trouble indication,

the Trouble LED will come ON, and the keypad sounder will

beep until a key is pressed.

[016] Fourth System Option Codes

1 ON AC Trouble Displayed 

If AC power fails, the condition will be reported to the moni-

toring station and will be indicated as a Trouble condition on

the system keypad.

OFF AC Trouble NOT Displayed 

If AC power fails, the condition will be reported, but the Trou-

ble LED will not light on the system keypad. If [*][2] is

entered to view the system troubles, Trouble #2 will still be

displayed.

2 ON Trouble Light Flashes if AC Fails 

Whenever AC power is lost from the system, the Trouble LED

will flash in the Ready and Armed modes within 30 seconds

after power is lost. When AC restores, the Trouble LED will

stop flashing within 30 seconds. If enabled, this option will

override the AC display option.

OFF Trouble Light does not follow AC Status 

3 ON Blank Keypad when not used 

If no keys are pressed for 30 seconds, all keypad lights turn

OFF and the display will blank until the next keypress, Entry

Delay, audible alarm or keypad buzzer condition.

OFF Keypad always Active 

The keypad lights will remain ON at all times.

4 ON Code Req’d to Remove Keypad Blanking 

Before a blanked keypad can be used, a valid access code

must be entered.

OFF No Code Required 

Pressing any key on a blanked keypad will remove the

blanking.

5 Future Use

6 ON Power Save Mode Enabled 

If AC power fails, all keypad lights will be shut OFF. The key-

pad lights will come back ON after a keypress, Entry Delay,

audible alarm or keypad buzzer condition except Door

Chime). The keypad lights will return to the off state after 30

seconds of keypad inactivity.

OFF Power Save Mode Disabled 

7 ON Bypass Status displayed While Armed 

The Bypass status light will be ON if there are zones bypassed

when the system is armed.

OFF Bypass Status NOT displayed While Armed 

The Bypass light will be ON only while the system is disarmed

to indicate that there are bypassed zones on the system.

When the system is armed, the Bypass light will be OFF.

8 Future Use

WWW.DIYALARMFORUM.COM

1 2 ... 23 24 25 26 27 28 29 30

WWW.DIYALARMFORUM.COM 1

Comentarios a estos manuales

Sin comentarios

DSC NT9005 V1.0 Especificaciones Pagina 28

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC NT9005 V1.0