DSC Power8 PC5OO5 Manual de instalación Pagina 11
- Pagina / 46
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
G E T T I N G S T A R T E D
7
2.3 Wire Routing for Power & Non-Power Limited
All wiring entry points are designated by the arrows. All circuits are classified UL installation power limited except for
the battery leads which are not power limited. A minimum ¼” (6.4mm) separation must be maintained at all points
between power limited and non-power limited wiring and connections.
Wire entry for power limited wiring must be separated by a different entry access from non-power
limited wiring.
2.4 Keybus Operation and Wiring
The Keybus is used by the panel to communicate with all modules
connected and by the modules to talk to the panel. The RED and BLK
terminals are used to provide power while YEL and GRN are clock
and data.
The 4 Keybus terminals of the panel must be connected to the 4
Keybus terminals or wires of all modules.
The following conditions apply:
• Keybus should be run in minimum 22 gauge quad (0.5mm), two pair
twist preferred
• the modules can be home run to the panel, connected in series or
can be T-tapped
• any module can be connected anywhere along the Keybus, you do
not need a separate Keybus wire run for keypads, zone expanders
etc.
• no module can be more than 1,000'/305m (in wire length) from the
panel
• shielded wire is not necessary unless wires are run in an area that
may present excessive RF noise or interference
Example of Keybus Wiring
B
C
A
PANEL
500’
500’
150’
150’
B
C
A
PANEL
500’
500’
150’
150’
NOTENOTE
NOTENOTE
NOTE: Module (A) is wired correctly as it is within 1,000'/305m of the panel, in
wire distance.
Module (B) is wired correctly as it is within 1,000'/305m of the panel, in
wire distance
Module (C) is NOT wired correctly as it is further than 1,000'/305m
from the panel, in wire distance.
2.5 Current Ratings - Modules and Accessories
In order for the Power 832 system to operate properly, the power output capabilities of the main control and
expansion devices must not be exceeded. Use the data presented below to ensure that no part of the system is
overloaded and cannot function properly.
System Outputs (all 12 V
DC)
• PC5010 VAUX: 500 mA. Includes one keypad. Subtract for each additional keypad, expansion module
and accessory connected to VAUX or Keybus.
BELL: 700 mA. Continuous Rating.
3.0 A. Short Term. Available only with standby battery connected.
• PC5200/PC5204 VAUX: 1.0 A. Continuous Rating. Subtract for each device connected (max. load for burglary
applications).
3.0 A. Short Term. Available only with standby battery connected.
• PC5208 VAUX: 250 mA. Subtract for each device connected. Subtract the total load on this terminal
from the PC5010 VAUX/Keybus output.
• PC5100 VAUX: 100 mA. Subtract for each device connected. Subtract the total load on this terminal
from the PC5010 VAUX/Keybus output.
• PC5108 VAUX: 100 mA. Subtract for each device connected. Subtract the total load on this terminal
from the PC5010 VAUX/Keybus output.
• PC5200 AUX: 1.0A max. (continuous). Subtract for each device connected. This rating applies for burglary
applications only.
PC5010 Device Ratings (@ 12 V
DC)
• LCD5500 Keypad: 50 mA • PC5208 Output Module: 50 mA
• PC5508Z Keypad: 80 mA • PC5132 Wireless Module: 125 mA
• PC5516Z Keypad: 90 mA • PC5100 Addressable Service Interface Module: 40 mA
• PC5532Z Keypad: 120 mA • Escort5580 Module: 150 mA
• LCD5500Z Keypad: 85 mA • PC5928 Audio Interface Module: 65 mA
• PC5936 Module: 100mA • PC5200 Power Supply: 20mA
• PC5400 Printer Module: 65 mA • PC5921 Intercom Audio Station: 20 mA
• PC5921 EXT Door Box Audio Station: 20 mA • LCD5501Z Keypad: 90mA
Keybus
NOTE: A minimum 1/4" (6.4mm) separation
must be maintained at all points between
power limited and non-power limited wiring
and connections.
- Installation 1
- LIMITED WARRANTY 2
- WARNING Please Read Carefully 2
- Table of Contents 3
- Hookup Diagram 4
- System Introduction 5
- 1.2 Additional Devices 6
- 1.3 Out of the Box 8
- Getting Started 9
- G E T T I N G S T A R T E D 10
- 2.7 Keypad Assignment 12
- 2.8 Enable Supervision 13
- 2.9 Removing Modules 13
- 2.10 Zone Wiring 13
- Loop Resistance Loop Status 14
- 5600Ω (contact closed) Secure 14
- 2.11 Keypad Zones 15
- Keypad Commands 16
- 3.3 Auto Bypass 17
- 3.4 [✱] Commands 17
- LCD keypad 18
- K E Y P A D C O M M A N D S 19
- 3.5 Function Keys 21
- How to Program 24
- 4.5 Viewing Programming 25
- Program Descriptions 26
- 5.2 Zone Attributes 27
- 5.3 Communicator - Dialing 28
- 5.8 Downloading 32
- 5.10 PGM Outputs 33
- 5.12 Siren 36
- 5.13 Test Transmission 36
- 5.15 Entry/Exit Delay Options 37
- 5.16 Event Buffer 37
- 5.17 Swinger Shutdown 38
- 5.18 Transmission Delay 38
- 5.19 Keypad Backlighting 38
- 5.21 Automatic Arming 38
- 5.22 Keypad Lockout 39
- 5.23 Keypad Blanking 39
- 5.24 Loop Response 39
- 5.25 Keypad Tampers 39
- 5.27 Wireless Expansion 40
- 5.28 Escort5580 Module 41
- 5.29 On-Site Printer 41
- 5.30 Audio Interface Module 41
- 5.31 Alternate Communicators 41
- 5.32 Default (Factory) 41
- 5.33 Installer Lockout 42
- 5.34 Walk Test (Installer) 42
- Reporting Codes 43
- REPORTINGV CODES 44
- Zone Reporting Codes 45
- FCC COMPLIANCE STATEMENT 46
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC Power8 PC5OO5
(32 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.170 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales