DSC Power8 PC5OO5 Manual de instalación descargar pdf (Pagina 19)

K E Y P A D C O M M A N D S

[✱]+[4] Door Chime On/Off

If enabled the keypad will beep 5 times rapidly when a zone is tripped and restored. The panel will only do this

for zones with the Door Chime attribute enabled and if the door chime feature is enabled

(See Section 5.2 “Zone

Attributes”)

To turn Door Chime on/off:

1. Press [✱] [4].

2. The keypad will beep 3 times rapidly when the Door Chime feature is enabled and one long beep when the

feature is disabled.

[✱]+[5] Programming Access Codes

There are 37 Access Codes available. They are as follows:

• Access Codes [01] to [32] . User Codes 1 to 32 • Access Code [40] ........... System Master Code

• Access Code [33] ............ Partition Duress Code • Access Code [41] ........... Partition Master Code

• Access Code [34] ............ Partition Duress Code • Access Code [42] ........... Partition Master Code

All Access Codes have the ability to arm/disarm any Partition(s) it is enabled for and activate the PGM Outputs using

the [✱][7][Access Code][1] and [✱][7][2] commands

(See Section 3.4 “[

✱

] Commands, [

✱

][7]”)

Additional Access Code Attributes are also programmable. Attributes determine what abilities the code will

have. The programmable attributes are as follows:

• Partition 1 Operation enable • Zone Bypass enable

• Partition 2 Operation enable • Escort5580 Access enable

User Codes - Access Codes [01] to [32]

Each User Code can be programmed to work on Partition 1, Partition 2 or both Partitions. In addition each can be

programmed to have the ability to bypass zones and remote access to the Escort5580.

“Master Code” attributes cannot change. By default, each code has the attributes of the code used to

program it.

Duress Codes - Access Codes [33] and [34]

When a Duress Code is used to perform any function the panel will report a Duress Reporting Code

(See

Section 5.7 “Communicator - Reporting Codes”)

Partition Master Codes - Access Codes [41] and [42]

Partition Master Codes can program additional User Codes and the Duress Code for their Partition.

System Master Code - Access Code [40]

By default the System Master Code is enabled to operate on both Partitions and can perform any keypad function.

This code can be used to program all User Codes as well as the Partition Master Codes and Duress Codes.

If the Master Code Not Changeable option is enabled the System Master Code can only be changed using

Installer Programming.

How to program Access Codes:

Programming Access Codes is a two step process. First the code must be programmed followed by the code

attributes.

1. Enter [✱] [5] [Master Code]. The keypad will flash the ‘Program’ light and turn on the zone light for any code

already programmed.

2. Enter the 2 digit number for the code you want to program. The corresponding zone light will flash.

3. Enter a four digit code, the zone light will turn on steady.

4. Continue with steps 2 and 3 until all codes are programmed.

Do not press [

✱

] or [#] when programming the access codes.

When programming Duress Codes or Partition Master Codes no zone light will flash.

After all the Codes have been programmed press the [#] key to return to the Ready mode.

How to program Access Code Attributes:

“Master Code” attributes cannot change. By default, each code has the attributes of the code used to

program phone access.

1. Enter [✱][5][Master Code]. The keypad will flash the ‘Program’ light and turn on the zone light for any code

already programmed.

2. Press [9] to enter the Attribute mode. The keypad will turn on the ‘Ready’ light and turn off the armed light.

3. Enter the 2 digit number for the code you want to program Attributes for. Zone lights [1] to [4] will be on or off.

Refer to the following chart:

• Zone Light 1 - ON - enable code for Partition 1 • Zone Light 3 - ON - enable Zone Bypass

• Zone Light 2 - ON - enable code for Partition 2 • Zone Light 4 - ON - enable Escort5580 Access

4. Enter [1] to [4] to turn the zone lights ON or OFF, then press [#] key.

5. Continue with steps 2 and 3 until all code attributes are programmed.

After all the codes and attributes have been programmed press the [#] key to exit Access Code Programming.

How to erase Access Code:

Select the code to be erased and press [✱].

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 45 46

Comentarios a estos manuales

Sin comentarios

DSC Power8 PC5OO5 Manual de instalación Pagina 19

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC Power8 PC5OO5