DSC Power8 PC5OO5 Manual de instalación Pagina 22
- Pagina / 46
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
K E Y P A D C O M M A N D S
18
3.5.1 Function Key Options
The following is a list of Function Key options available:
[00] - Null Key
The key is not used and will perform no function when pressed.
[01] - Select Partition 1
Provides an easy way to select Partition 1 operation from a Partition 2 keypad. This is the same as pressing and
holding the [#] key then pressing and holding the [1] key to select Partition 1 from a Partition 2 keypad
(See
Section 3.6 “Global and Partition Keypad Operation”)
.
[02] - Select Partition 2
Provides an easy way to select Partition 2 operation from a Partition 1 keypad. This is the same as pressing and
holding the [#] key then pressing and holding the [2] key to select Partition 2 from a Partition 1 keypad
(See
Section 3.6 “Global and Partition Keypad Operation”)
.
[03] - Stay Arm
Same as described in Function Keys - Section 3.5.
[04] - Away Arm
Same as described in Function Keys - Section 3.5.
[05] - [✱]+[9] No-Entry Delay Arm
After this function key is pressed the user must enter a valid user code. The Partition will arm and remove entry
delay from the partition when the exit delay expires
(See Section 3.4 “[
✱
] Commands, [
✱
] [9] Arming without
entry delay”)
.
[06] - [✱]+[4] Door Chime On/Off
This function key provides the user a simple method for turning the Door Chime feature on and off
(See Section
3.4 “[
✱
] Commands, [
✱
] [4] Door chime on/off”)
.
[07] - [✱]+[6]...[4] System Test
This function key provides the user with a simple method for testing the system
(See Section 3.4 “[
✱
]
Commands, [
✱
] [6] User functions”)
.
[08] - [✱]+[1] Bypass Mode
This function key provides the user with a simple method for entering the Bypass Mode. If a user code is required
it must be entered before bypassing can be performed
(See Section 3.4 “[
✱
] Commands, [
✱
] [1] Zone Bypass”)
.
[09] - [✱]+[2] Trouble Display
This function key provides the user with a simple method for entering the Trouble Display Mode
(See Section 3.4
“[
✱
] Commands, [
✱
]+[2] Trouble display”
).
[10] - [✱]+[3] Alarm Memory
This function key provides the user with a simple method for entering the Alarm Memory Display Mode
(See
Section 3.4 “[
✱
] Commands, [
✱
] [3] Alarm memory”)
.
[11] - [✱]+[5] Programming Access Codes
This function key provides the user with a simple method for programming user codes. After this key is pressed
a valid System Master or Partition Master will have to be entered before the panel will allow programming to be
performed
(See Section 3.4 “[
✱
] Commands, [
✱
] [5] Programming Access Codes”)
.
[12] - [✱]+[6] User Functions
This function key provides the user with a simple method for programming User Functions. After this key is
pressed a valid System Master or Partition Master must be entered before the panel will allow User Functions to
be performed
(See Section 3.4 “[
✱
] Commands, [
✱
] [6] User functions”)
.
[13] - [✱]+[7]+[1] Command Output Option 1
This function key provides the user with a simple method for activating a PGM Output programmed as
Command Output Option 1
(See Section 5.10 “PGM Outputs”)
. By default, after this key is pressed a valid user
code must be entered
(See Section 3.4 “[
✱
] Commands, [
✱
] [7] Command output functions”)
.
[14] - [✱]+[7]+[2] Smoke Detector Reset
This function key provides the user with a simple method for activating a PGM output programmed as either
option [03] Sensor Reset or [20] Command Output option 2.
[15] - General Voice Prompt Help
This feature can only be programmed if both the Escort5580 and the PC5928 Audio Matrix module are being used.
When the function key is pressed, the intercoms will perform a Help page. The user must then press the Page/
Answer button on any intercom station to begin the help session with the Escort. For more information, please
refer to the PC5928
Installation Manual
.
[16] - [✱]+[0] Quick Exit
Same as described in Function Keys - Section 3.5.
[17] - [✱]+[1] Reactivate Stay/Away Zones
This function key provides the user with a simple method for adding Stay/Away zones back into the system at night-
time
(See Section 3.4 “[
✱
] Commands, [
✱
] [1] Reactivate Stay/Away zones”)
.
- Installation 1
- LIMITED WARRANTY 2
- WARNING Please Read Carefully 2
- Table of Contents 3
- Hookup Diagram 4
- System Introduction 5
- 1.2 Additional Devices 6
- 1.3 Out of the Box 8
- Getting Started 9
- G E T T I N G S T A R T E D 10
- 2.7 Keypad Assignment 12
- 2.8 Enable Supervision 13
- 2.9 Removing Modules 13
- 2.10 Zone Wiring 13
- Loop Resistance Loop Status 14
- 5600Ω (contact closed) Secure 14
- 2.11 Keypad Zones 15
- Keypad Commands 16
- 3.3 Auto Bypass 17
- 3.4 [✱] Commands 17
- LCD keypad 18
- K E Y P A D C O M M A N D S 19
- 3.5 Function Keys 21
- How to Program 24
- 4.5 Viewing Programming 25
- Program Descriptions 26
- 5.2 Zone Attributes 27
- 5.3 Communicator - Dialing 28
- 5.8 Downloading 32
- 5.10 PGM Outputs 33
- 5.12 Siren 36
- 5.13 Test Transmission 36
- 5.15 Entry/Exit Delay Options 37
- 5.16 Event Buffer 37
- 5.17 Swinger Shutdown 38
- 5.18 Transmission Delay 38
- 5.19 Keypad Backlighting 38
- 5.21 Automatic Arming 38
- 5.22 Keypad Lockout 39
- 5.23 Keypad Blanking 39
- 5.24 Loop Response 39
- 5.25 Keypad Tampers 39
- 5.27 Wireless Expansion 40
- 5.28 Escort5580 Module 41
- 5.29 On-Site Printer 41
- 5.30 Audio Interface Module 41
- 5.31 Alternate Communicators 41
- 5.32 Default (Factory) 41
- 5.33 Installer Lockout 42
- 5.34 Walk Test (Installer) 42
- Reporting Codes 43
- REPORTINGV CODES 44
- Zone Reporting Codes 45
- FCC COMPLIANCE STATEMENT 46
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC Power8 PC5OO5
(32 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales