DSC Power8 PC5OO5 Manual de instalación descargar pdf (Pagina 27)

P R O G R A M D E S C R I P T I O N S

Do not wire 24-Hour Supervisory zones on keypad zone terminals.

[10] 24 Hour Supervisory Buzzer Zone Whether armed or disarmed, when this zone type is violated the panel will

immediately latch the keypad buzzer until a valid user code is entered and will communicate immediately to the

central station.

[11] 24 Hour Burglary Zone If this zone is violated, whether armed or disarmed, the panel will immediately latch

the alarm output and communicate to the central station. The alarm will sound for the Bell Cutoff time

programmed in

Section [005] “System Times”

or until a valid user code is entered.

[12]-[20] The following zone definitions operate similar to the 24 Hour Burglary except for System Event output type and

SIA identifier:

[12] 24 Hour Holdup Zone [15] 24 Hour Medical Zone [18] 24 Hour Sprinkler Zone

[13] 24 Hour Gas Zone [16] 24 Hour Panic Zone [19] 24 Hour Water Flow Zone

[14] 24 Hour Heat Zone [17] 24 Hour Emergency Zone [20] 24 Hour Freezer Zone

NOTE: [12] 24 Hour Holdup zones give a silent alarm by default.

[21] 24 Hour Latching Tamper If this zone is violated the installer must enter Installer Programming before the

panel will allow either Partition to be armed.

[22] Momentary Keyswitch Arm Zone Momentary violation of this zone will alternately arm/disarm the Partition the

zone is assigned to. This zone type should not be programmed as global.

[23] Maintained Keyswitch Arm Zone When this zone is violated, the partition it is assigned to will arm. When this

zone is secured, the partition will disarm. This zone should not be programmed as global zone.

Do not program wireless zones as [21] or [23] Keyswitch or as [24] LINKS Answer zones.

[24] LINKS Answer Zone If the LINKS1000 cellular communicator is being used it is possible to perform

downloading through the unit if the phone line is disconnected. If this is required connect the RING terminal of

the LINKS1000 to this zone. Refer to the LINKS1000 Installation sheet for more information.

Do not wire LINKS Answer zones on keypad zone terminals.

[87] Delayed 24 Hour Fire (Wireless) This zone type operates the same as [07] Delayed 24 Hour Fire Zone and

must be used if the smoke detector is wireless.

[88] Standard 24 Hour Fire (Wireless) This zone type operates the same as [08] Standard 24 Hour Fire Zone and

must be used if the smoke detector is wireless.

5.1.1 Assigning Keypad Zones

Each keypad has a zone input to which a device—such as a door contact—can be connected. (See Section

2.12 “Keypad Zones” for wiring information.)

Once the keypad zones are installed, assign the zone in programming section [020] Keypad Zone

Assignments.

Enter the 2 digit zone designated for each keypad (slot) from 01-08.

Keypad Zone Assignments ................................... [020]

5.2 Zone Attributes

Each zone will operate according to the Zone Definition selected for it

(See Section 5.1 “Zone Definitions”)

Additional zone attributes can be programmed to customize the operation of a zone for a specific application.

The following attributes are programmable by zone:

Attributes for Fire Zones should not be changed from default.

Audible/Silent Determines whether the zone will activate the alarm output or will be silent.

Pulsed/Steady Determines if the alarm output will be steady or pulse on for 1 second and off for one second.

Activate Chime Determines if the zone will activate the chime feature

(See Section 3.4 “[

✱

] Commands, [

✱

] [4]

Door Chime ON/OFF”).

Bypass Enable Determines if the zone can be manually bypassed

(See Section 3.4 “[

✱

] Commands, [

✱

] [1] -

Zone Bypass”)

Force Arm Enable

(Shall not be enabled on UL Listed systems)

Determines if the system can be armed with

the zone violated. At the end of exit delay, if this type of zone is violated, it will be ignored by the panel. Once

the zone is secured it will be added back into the system.

This zone attribute is useful for a garage door. The customer can arm the system with the garage door open.

Later when the customer closes the door it becomes part of the system.

NOTE: 24-hour zones must not have Force Arm enabled.

Swinger Shutdown Enable

(Shall not be enabled on UL Listed systems)

Determines if the panel will shut

down the communicator for the zone after the swinger limit is reached

(See Section 5.17 “Swinger Shutdown”)

Transmission (TX) Delay Enable Determines if the panel will delay communicating the alarm reporting code

to the central station (See Section 5.18 “Transmission Delay”).

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 45 46

Comentarios a estos manuales

Sin comentarios

DSC Power8 PC5OO5 Manual de instalación Pagina 27

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC Power8 PC5OO5