DSC Power832 PC5O15 Manual de instalación descargar pdf (Pagina 27)

P R O G R A M D E S C R I P T I O N S

24

Force Arm Enable Determines if the system can be armed with the zone violated. At the end of exit delay, if this type

of zone is violated, it will be ignored by the panel. Once the zone is secured it will be added back into the system.

This zone attribute is useful for a garage door. The customer can arm the system with the garage door open.

Later when the customer closes the door it becomes part of the system.

NOTE: 24-hour zones must not have Force Arm enabled.

Swinger Shutdown Enable

Determines if the panel will shut down the communicator for the zone after the

swinger limit is reached

(See Section 5.17 “Swinger Shutdown”)

.

Transmission (TX) Delay Enable Determines if the panel will delay communicating the alarm reporting code

to the central station (See Section 5.7.1 “Transmission Delay”).

Do not use the transmission delay on Downlook zones.Do not use the transmission delay on Downlook zones.

Do not use the transmission delay on Downlook zones.

Wireless Zone Determines if the zone is a wireless zone or a hardwired zone. Allows the panel to generate low

battery trouble and zone supervisories.

The wirThe wir

The wir

eless zone attribute must be set enabled for all enreless zone attribute must be set enabled for all enr

eless zone attribute must be set enabled for all enr

olled wirolled wir

olled wir

eless zones.eless zones.

eless zones.

Zones 1 to 32 Attributes ......................................... Section [101] - [132]

Audible/Silent Alarm ............................................... Section [101] - [132], Option [1]

Pulsed/Steady Alarm .............................................. Section [101] - [132], Option [2]

Activate Chime ........................................................ Section [101] - [132], Option [3]

Bypass Enable ........................................................ Section [101] - [132], Option [4]

Force Arm Enable ................................................... Section [101] - [132], Option [5]

Swinger Shutdown Enable ..................................... Section [101] - [132], Option [6]

Transmission Delay Enable .................................... Section [101] - [132], Option [7]

Wireless Zone ......................................................... Section [101] - [132], Option [8]

5.3 Communicator - Dialing

If the Communicator Disable option is selected the panel will not attempt to call central station. If enabled the panel will

attempt to call central station when an event occurs that has a valid reporting code programmed

(See Section 5.7

“Communicator - Reporting Code”).

You must also program a valid telephone number. Communicator Call Direction

Options are used to select which phone number the panel will dial when an event occurs.

If DTMF Dialing

is enabled the panel will dial using DTMF (touch tone). If Switch to Pulse Dial is enabled the

panel will switch to pulse dialing on the 5th attempt to call the central station. If disabled the panel will always

dial DTMF.

If DTMF Dialing

is disabled the panel will always pulse dial.

The Post Dial Wait for Handshake

determines the amount of time the panel will wait for a valid handshake from the

receiver. If the panel does not hear the handshake it will consider the call a failed attempt, hang up and try again.

The Maximum Dialing Attempts determines the maximum number of attempts the panel will make to send a signal

to the central station before indicating a Failure to Communicate (FTC) trouble condition. The 3rd Phone Number can

be used to back up the 1st in this situation

(see section 5.4 “Communicator - Phone Numbers”).

For UL Listed pr For UL Listed pr

For UL Listed pr

oducts, dialing attempts must be no less than 5, no groducts, dialing attempts must be no less than 5, no gr

oducts, dialing attempts must be no less than 5, no gr

eater than 10 attempts.eater than 10 attempts.

eater than 10 attempts.

Pulse Dialing ........................................................... Section [380], Option [3]

Switch to Pulse Dial ................................................ Section [380], Option [4]

Post Dial Wait for Handshake ................................ Section [161]

Maximum Dialing Attempts .................................... Section [160]

Communicator Disable ........................................... Section [380], Option [1]

Communicator Call Direction Options ................... Section [361] to [368]

5.4 Communicator - Phone Numbers

The panel can call 3 different phone numbers for communication to central station. The 1st Phone Number is

the primary number, the 2nd Phone Number is the secondary number and the 3rd Phone Number will back up

the 1st phone number if enabled.

The 3rThe 3r

The 3r

d Phone Number will NOT back up the 2nd Phone Numberd Phone Number will NOT back up the 2nd Phone Number

d Phone Number will NOT back up the 2nd Phone Number

..

.

If

Alternate Dial Alternate Dial

Alternate Dial is enabled the panel will alternate between the 1st and 3rd phone numbers when attempting to

call the central station. If disabled the panel will only attempt to call the 3rd phone number after failing to

communicate on the 1st phone number.

For AlterFor Alter

For Alter

nate Dial to work prnate Dial to work pr

nate Dial to work pr

operly the 3roperly the 3r

operly the 3r

d Phone Number must be enabled.d Phone Number must be enabled.

d Phone Number must be enabled.

Phone numbers can be up to 32 digits which will allow you to add special digits if required. To program the

phone number enter numbers 0 through 9 as required. The following is a list of HEX digits which can also be

programmed and the function they perform:

HEX (B) - simulates the [✱] key on a touch tone phone HEX (E) - forces the panel to pause for 2 seconds

HEX (C) - simulates the [#] key on a touch tone phone HEX (F) - end of phone number marker

HEX (D) - forces the panel to search for dial tone

DSC Power832 PC5O15 Manual de instalación Pagina 27

Comentarios a estos manuales

DSC Power832 PC5O15 Manual de instalación Pagina 27

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC Power832 PC5O15