DSC PC 1555 Manual de instalación descargar pdf (Pagina 33)

NOTE:

DO NOT change Fire zones attributes from the

default settings.

[165] - Maximum Dialing Attempts To Each Phone

Number

This value represents the number of attempts that will be

made to each telephone number when communicating.

The default value is 007 attempts. Valid entries are 001-015.

NOTE:

The PC1555 CP-01 will not allow more than 15 dial-

ing attempts to a single phone number. If a value higher

than 15 is programmed in Section [165], the panel will still

only make15 attempts.

[166] - Post-Dial Wait For Handshake

This value represents the time the communicator waits

for a valid initial handshake from the receiver after dial-

ing the programmed telephone number. The default

value is 040 seconds.

[167] - T-Link Interface Communications Wait for

Acknowledge

This value represents the time the communicator waits

for an ACK from the receiver after sending a SIA Packet.

The default is 020 seconds.

[170]-[178] Timers

[170] - PGM Output Timer

This value represents the period of time (in seconds) that a

PGM will activate if programmed to follow the PGM

Timer.

The default value is 005 seconds. Valid entries are 001-255.

NOTE:

This option does not affect outputs programmed as

Sensor Reset (Type 03).

NOTE:

If a System Event PGM is programmed to follow the

Command Output Timer, all attributes must be enabled.

[175] - Auto-arm Postpone Timer

This feature controls the sequence of events after a valid

access code is entered during the Auto-arm Pre-alert. If

the Auto-arm Postpone Timer is programmed as 000, the

Auto-arm will be cancelled. If a value between 001 and

255 is programmed, then the Auto-arm will be postponed

for the corresponding number of minutes and the panel

will resume normal operation. The panel will also log the

appropriate user log for the access code which postponed

the arming. When the postpone time expires, the panel

Auto-arm Pre-alert will be re-initiated. The Auto-arm can

be postponed multiple times. If the Auto-arm is post-

poned, arming or disarming the panel will not affect the

postpone sequence.

[176] - Cross Zone/Police Code Timer

This option affects the Cross Zone Police Code log and

transmission as well as the Cross Zone feature.

When a zone trip occurs, the Cross Zone Timer starts.

This timer affects the panel in two different ways depend-

ing on the programming of the Burglary Verification

Options (Section [018], Option 6):

• If the Police Code feature is being used, the first zone

alarm will immediately transmit. If a second zone

alarm occurs in the time period (minutes) pro-

grammed in this section, the panel will log and trans-

mit the Police Code event. If the second zone alarm

occurs after this timer expires, the Police Code will not

be logged or transmitted, and the timer will restart.

• If the new Cross Zone attribute is used, the first zone

alarm will not log or transmit. If a second zone is vio-

lated within the Cross Zone Timer’s duration (sec-

onds), the panel will go into the appropriate alarm

sequence and will communicate both zone alarms. No

Police Code is sent.

NOTE:

If 000 is programmed in this section, either: the

Police Code will transmit for any two different zone alarms

during an armed-to-armed period or the new Cross Zoning

feature will not work. This is not a valid entry for Cross Zon-

ing.

[101]-[132] ZONE ATTRIBUTES

Option Attribute On/Off Description

1BellON

An alarm will cause the bell output to activate.

OFF Silent Alarm

2Bell TypeON

The bell output will be steady when the zone is in alarm.

OFF

The bell output will pulse when the zone is in alarm.

3ChimeON

Every keypad will chime when the zone is violated and when the zone is secured. Door Chime

will work in both the armed and disarmed states.

OFF

The zone will not chime the keypads.

4 Bypass ON

The zone can be manually bypassed.

OFF

The zone cannot be bypassed.

5 Force Arming ON

The system (partition) can be armed with the zone violated. The zone will be temporarily

bypassed, and when the zone is secured it will be added back into the system.

OFF

The system cannot be armed if this zone is open.

6 Swinger Shutdown ON

The zone will shut down after a programmed number of alarms, inhibiting further transmissions

to the monitoring station. The bell can follow swinger shutdown if programmed.

OFF Swinger Shutdown Disabled

7 Transmission Delay ON

The reporting of zone alarms will be delayed for the programmed time. If a valid access code is

entered within this time, no alarm signal will be communicated.

OFF

When an alarm occurs, the reporting code is transmitted immediately.

NOTE: Transmission Delay cannot be used on fire zones.

8 Wireless ON Zone is Wireless.

The zone will ignore the main board zone (if applicable) and respond to the

corresponding zone enrolled on the PC5132.

OFF Zone is Hardwired.

The zone uses the corresponding hardwired zone.

9 Cross Zone ON Zone is a Cross Zone

. Zone is enabled for Cross Zoning.

OFF Zone is not a Cross Zone.

Zone is not enabled for Cross Zoning. The default state for the Cross

Zone attribute is OFF for all zone types.

NOTE: DO NOT change Fire Zones attributes from the default settings.

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 55 56

Comentarios a estos manuales

Sin comentarios

DSC PC 1555 Manual de instalación Pagina 33

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC PC 1555