DSC PC 1555 Manual de instalación descargar pdf (Pagina 37)

Output #1 on the PC5200/PC5204 Power Supply/Out-

put Module.

General System Supervisory Trouble:

a General System

General SystemGeneral System

General System

Supervisory Trouble

Supervisory TroubleSupervisory Trouble

Supervisory Trouble reporting code will be transmitted if

any module goes missing from the Keybus. If the module

is a zone expander the panel will also transmit the

Zone

Expander Supervisory Alarm Trouble

reporting code.

[346] - Maintenance Restoral Reporting Codes

Battery Trouble Restoral

Battery Trouble RestoralBattery Trouble Restoral

Battery Trouble Restoral: the Battery Trouble Restora

Battery Trouble RestoraBattery Trouble Restora

Battery Trouble Restoral

reporting code will not be transmitted until the battery

has been charged over 12.5 V

AC Failure Trouble Restoral

AC Failure Trouble RestoralAC Failure Trouble Restoral

AC Failure Trouble Restoral: the AC Failure Trouble

AC Failure TroubleAC Failure Trouble

AC Failure Trouble

Restoral

RestoralRestoral

Restoral

reporting code will be transmitted once AC

power has been restored for the amount of time pro-

grammed for AC Failure Communication delays.

Bell Circuit Trouble Restoral

Bell Circuit Trouble RestoralBell Circuit Trouble Restoral

Bell Circuit Trouble Restoral: the Bell Circuit Trouble

Bell Circuit TroubleBell Circuit Trouble

Bell Circuit Trouble

Restoral

RestoralRestoral

Restoral reporting code will be transmitted as soon as the

open condition on the bell output is corrected.

Fire Trouble Restoral

Fire Trouble RestoralFire Trouble Restoral

Fire Trouble Restoral: the Fire Trouble Restoral

Fire Trouble RestoralFire Trouble Restoral

Fire Trouble Restoral reporting

code will be transmitted when the correct resistance value

is measured on any Fire type zone.

Auxiliary Power Supply Trouble Restoral

Auxiliary Power Supply Trouble RestoralAuxiliary Power Supply Trouble Restoral

Auxiliary Power Supply Trouble Restoral: the panel con-

stantly checks the AUX output, when the excessive cur-

rent draw is removed the panel will reset the output and

transmit an Auxiliary Power Supply Trouble Restoral

Auxiliary Power Supply Trouble RestoralAuxiliary Power Supply Trouble Restoral

Auxiliary Power Supply Trouble Restoral

reporting code.

TLM Restoral:

TLM Restoral:TLM Restoral:

TLM Restoral: the TLM Restoral reporting code will be

transmitted immediately after the Trouble is restored.

General System Trouble Restoral

General System Trouble RestoralGeneral System Trouble Restoral

General System Trouble Restoral: a General System Trou-

ble Restoral

reporting code will be transmitted when the

panel detects none of the following:

AC Power Failure Low Battery

AUX Output Trouble Output #1 on the PC5200 /

PC5204 power Supply/Output Module after a Trouble

was reported.

General System Supervisory Restoral

General System Supervisory RestoralGeneral System Supervisory Restoral

General System Supervisory Restoral: the General System

Trouble Restoral reporting code will be transmitted when

the control panel detects all modules enrolled on the key-

bus

[347] - Miscellaneous Maintenance Reporting Codes

Telephone Number 1 (2) FTC Restore:

Telephone Number 1 (2) FTC Restore:Telephone Number 1 (2) FTC Restore:

Telephone Number 1 (2) FTC Restore: if the panel fails to

transmit information to the central station it will display a

failure to communicate Trouble condition. The panel will

transmit a Phone Number 1 Failure

Phone Number 1 FailurePhone Number 1 Failure

Phone Number 1 Failure to Communicate

reporting code or a

Phone Number 2 Failure to Communi-

cate

reporting code the next time it calls the central sta-

tion. The panel will transmit the old events, followed by

the failure to communicate, followed by the new events.

Event Buffer 75% Full:

Event Buffer 75% Full:Event Buffer 75% Full:

Event Buffer 75% Full: If the event buffer is uploaded on a

regular basis an Event Buffer 75% Full

Event Buffer 75% FullEvent Buffer 75% Full

Event Buffer 75% Full reporting code can

be transmitted to warn that the Buffer is almost full.

DLS Lead In:

DLS Lead In:DLS Lead In:

DLS Lead In: The DLS Lead In

DLS Lead InDLS Lead In

DLS Lead In reporting code will only

be transmitted if the DLS Call Back feature is being used

(see Section 5.8 "Downloading"). Before the panel calls the

computer back it will call the central station and transmit

the reporting code to indicate a download session is

about to begin.

DLS Lead Out:

DLS Lead Out:DLS Lead Out:

DLS Lead Out: After a downloading session is attempted

and/or completed, the panel will transmit a DLS Lead

DLS LeadDLS Lead

DLS Lead

Out

OutOut

Out reporting code.

Zone Fault Alarm:

Zone Fault Alarm:Zone Fault Alarm:

Zone Fault Alarm: The Zone Fault Alarm

Zone Fault AlarmZone Fault Alarm

Zone Fault Alarm reporting code

will be transmitted when there is a short detected on any

DEOL zone and/or a loss of Supervisory on a wireless

zone.

Zone Fault Restoral:

Zone Fault Restoral:Zone Fault Restoral:

Zone Fault Restoral: The Zone Fault Restoral

Zone Fault RestoralZone Fault Restoral

Zone Fault Restoral reporting

code will be transmitted when the fault condition on the

zone is corrected.

Delinquency Code:

Delinquency Code:Delinquency Code:

Delinquency Code: The Delinquency

DelinquencyDelinquency

Delinquency reporting code is

sent whenever the panel is not armed within the number

of days programmed for the Delinquency Transmission

Delay.

General Zone Low Battery Alarm:

General Zone Low Battery Alarm:General Zone Low Battery Alarm:

General Zone Low Battery Alarm: the panel will transmit

a General Zone Low Battery Alarm

General Zone Low Battery AlarmGeneral Zone Low Battery Alarm

General Zone Low Battery Alarm reporting code when

a wireless detector indicates a low battery condition and

the delay programmed in Zone Low Battery Transmission

Delay expires.

General Zone Low Battery Restoral:

General Zone Low Battery Restoral:General Zone Low Battery Restoral:

General Zone Low Battery Restoral: the General Zone

Low Battery Restoral reporting code will be transmitted

when the low battery condition on all wireless zones is

corrected. The specific zone that caused the trouble will

be stored to the event buffer.

Installer Lead In:

Installer Lead In:Installer Lead In:

Installer Lead In: a reporting code will be sent to the cen-

tral monitoring station when Installer Programming is

entered through the keypad.

Installer Lead Out:

Installer Lead Out: Installer Lead Out:

Installer Lead Out: a reporting code will be sent to the

central monitoring station when Installers programming

is exited.

[348] - Test Transmission Reporting Codes

Walk Test End:

the Walk Test End

Walk Test EndWalk Test End

Walk Test End reporting code will be

transmitted when a Walk Test is terminated.

Walk Test Begin:

the Walk Test Begin

Walk Tes t B e g i n Walk Test Begin

Walk Test Begin reporting code will

be transmitted when a Walk Test is initiated.

Periodic Test Transmission with Trouble

Periodic Test Transmission with TroublePeriodic Test Transmission with Trouble

Periodic Test Transmission with Trouble - the panel can be

programmed to transmit a Periodic Test Transmission

Periodic Test TransmissionPeriodic Test Transmission

Periodic Test Transmission

with Trouble reporting code in place of the standard Peri-

odic Test Transmission if any of the following conditions

exist.

• Fire Zone Trouble (Zones 1-32)

• Battery Trouble (PC1555 CP-01, PC520X)

• Fire Zone Alarm (Zones 1-32, Two-Wire Smoke

• Aux Trouble (PC1555 CP-01)

• Fire Trouble (2-wire Smoke)

• Bell Trouble (PC1555 CP-01)

• Fire Tamper/Low Sensitivity (Wireless)

•Module Supervisory

• Fire Zones Bypassed (Zones 1-32)

• Fire Supervisory (Wireless)

• TLM Trouble (PC1555 CP-01)

• AC Trouble (PC1555 CP-01, PC520X)

• FTC Trouble

Periodic Test Transmission:

the Periodic Test Transmission

reporting code will be transmitted at the specified time,

(programmed in Section 378) every X number of days (see

Section 377).

System Test:

the System Test reporting code will be trans-

mitted when a system test is performed on the panel.

Links 1000 Test Transmission Code:

the Links1000 Test

Transmission reporting code will be transmitted via the

LINKS1000 cellular transmitter at the programmed inter-

val (see ‘Test Transmission Cycles’ section [377]) and time

of day (see Section [378]) of the LINKS Periodic Test

Transmi ss ion.

NOTE:

To disable this transmission of this reporting code, 00

must be entered.

[350] - Communicator Format Options

Communicator - Reporting Formats

Communicator - Reporting FormatsCommunicator - Reporting Formats

Communicator - Reporting Formats

Each central station telephone number of the panel can be

programmed to report using any one of the 5 formats

available. The following formats are supported: Pulse (10

and 20 bps), Contact ID, SIA, Residential Dial and a Pager

format. The following is a description of each.

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 55 56

Comentarios a estos manuales

Sin comentarios

DSC PC 1555 Manual de instalación Pagina 37

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC PC 1555