DSC PC 1555 Manual de instalación descargar pdf (Pagina 42)

3 SIA Reporting Codes ON SIA Sends Programmed Reporting Codes.

This option is for use with the SIA communication

format.). If 00 is programmed in the reporting code section, the event will not be communi-

cated. When this option is ON and there is a valid reporting code programmed in the reporting

code section, the programmed reporting code will be transmitted. If FF is programmed as a

reporting code, the event will not be communicated.

Reporting Code Entry Option ON Option OFF

00 No Transmission No Transmission

FF No Transmission Auto Reporting Code sent

01-FE 01-FE sent Auto Reporting Code sent

OFF SIA Sends Automatic Reporting Codes

. When this option is OFF and there is a valid reporting

code (01-FE) or FF programmed in the reporting code section, the panel will transmit an auto-

matic reporting code for SIA only. This would be used when automatic reporting codes are

required but there is a requirement for a different reporting code (e.g., Pager format, etc.).

4 Closing Confirmation ON Closing Confirmation Enabled

. When a Closing reporting code is successfully transmitted to

a programmed telephone number, the keypad will sound a series of 8 beeps to confirm to the

end user that the Closing code was sent and received.

OFF Closing Confirmation Disabled.

There will be no keypad ringback when a Closing reporting

code is successfully transmitted to a programmed telephone number.

5 Talk/Listen Options for

Phone Number One/Three

ON Talk/Listen (PC5936) on Phone #1/3 Enabled.

If Talk/Listen is requested for an event by the

PC5936, the panel will request the session on the next communication on phone number 1/3

(via L-Block) to the central station.

OFF Talk/Listen (PC5936) on Phone #1/3 Disabled.

The panel will not request a Talk/Listen session

for an event even if the PC5936 has requested it.

6 Talk/Listen Options for

Phone Number Two

ON Talk/Listen (PC5936) on Phone #2 Enabled.

If Talk/Listen is requested for an event by the

PC5936, the panel will request the session on the next communication on phone number 2 (via

L-Block) to the central station.

OFF Talk/Listen (PC5936) on Phone #2 Disabled.

The panel will not request a Talk/Listen session

for an event even if the PC5936 has requested it.

7 Contact I.D. Reporting Codes ON Contact I.D. Uses Programmed Reporting Codes.

The Contact I.D. communications format

will use programmed reporting codes when transmitting to the central station.

OFF Contact I.D. Uses Automatic Reporting Codes.

The Contact I.D. communications format will use

the automatic reporting codes as shown in Appendix C when transmitting to the central station.

8Not Used

[381] - SECOND COMMUNICATOR OPTION CODES

Option Communicator Code On/Off Description

[382] - THIRD COMMUNICATOR OPTION CODES

Option Communicator Code On/Off Description

1 Contact I.D. Partial Closing

Identifier

ON Partial Closing Identifier = 5.

Contact I.D. uses 5 as the identifier for the Partial Closing event.

OFF Partial Closing Identifier = 4.

Contact I.D. uses 4 as the identifier for the Partial Closing event.

This option is defaulted OFF.

2 Walk Test Communication ON Zone Alarms Communicate during Walk Test Enabled.

Zone alarms that occur during Walk

Test will communicate if programmed to do so.

OFF Zone Alarms Communicate during Walk Test Disabled.

Zone alarms that occur during Walk

Test will not communicate even if programmed.This option is defaulted OFF. NOTE: This

option must be OFF for SIA FAR installations.

3 Communications Cancelled

Message

ON Communications Cancelled Message Enabled.

The ’Communications Cancelled’

(LCD5500Z/LCD5520Z) or ’CC’ (LCD5501Z) message will be displayed if alarms are acknowl-

edged during the Transmission Delay time. This message will be displayed for 5 seconds on all

keypads on the system. The acknowledgment can be from an access code, disarm function key,

or a keyswitch zone. Caution: This option must NOT be turned OFF for SIA-FAR installa-

tions.

OFF Communications Cancelled Message Disabled.

The ’Communications Cancelled’ message

will not be displayed. This option is defaulted OFF.

4 Call Waiting Cancel ON Call Waiting Cancel Enabled.

The Call Waiting dialing string programmed in Section [304] will

be dialed before the first attempt of each phone number. All subsequent dialing attempts to the

same phone number will not use the Call Waiting Cancel dialing string.

OFF Call Waiting Cancel Disabled.

The Call Waiting dialing string will not be dialed. This option is

defaulted OFF. Note: A Call Waiting Cancel on a non-call waiting line will prevent successful

connection to the central station.

5T-Link ON

The panel will communicate with a T-Link module connected to the PC-Link header.

OFF

The T-Link interface is disabled.

*NOTE: Not investigated by UL.

6 AC Failure Transmission

Delay

ON AC Failure Transmission Delay

. Delay is in hours.

NOTE: For central & remote fire applications, this option must be ON.

OFF AC Failure Transmission Delay

. Delay is in minutes.

7-8 ON

For Future Use

1 2 ... 37 38 39 40 41 42 43 44 45 46 47 ... 55 56

Comentarios a estos manuales

Sin comentarios

DSC PC 1555 Manual de instalación Pagina 42

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC PC 1555