DSC PC 1555 Manual de instalación descargar pdf (Pagina 35)

[301] - First Telephone Number

[302] - Second Telephone Number

[303] - Third Telephone Number

NOTE:

There is a static delay of 2 seconds before any addi-

tional dial tone search in a phone number.

NOTE:

The panel will not attempt to communicate, if no

phone number is programmed. This applies to phone num-

bers 1, 2 and 3.

[304] - Call Waiting Cancel Dialing String

This is a 6-digit Hex entry that is used to disable Call

Waiting on a Call Waiting-equipped phone line. This is

typically *70 in most areas. Dialing this string before a

phone number will disable Call Waiting for the duration

of the call. If this section is programmed (not FF), and Sec-

tion 382, Option 4 is ON, the panel will dial this string in

place of the first digit of the phone number (Sections

[301]-[303]). This only applies to the first attempt that is

made to each phone number.

NOTE:

If not all 6 digits are required they should be filled

with Hex F.

All 6 digits of this section need to be programmed in

order for any changes to be accepted.

Communicator - Account Codes

The System Account Code will be used by the panel

when communicating System events (e.g. Low Battery,

Test Transmission). This account code can be up to six

digits in length for the SIA Communications format. Only

the SIA reporting format supports six-digit account

codes. All other formats will use the first four digits of the

account code.

NOTE:

If the communicator is programmed for the SIA

reporting format, the system will use this account code for

all partitions.

There is 1 Partition Identifier Codes

Partition Identifier Codes Partition Identifier Codes

Partition Identifier Codes (or account codes)

programmable, for the system. The account code is used

by central station to determine which panel is calling.

The panel will report using partition 1 account code.

[310] - System Account Code

This is the account code used by the panel when communi-

cating System events (e.g., Low Battery, Test Transmission).

This account code can be up to six digits in length for the

SIA Communications format.

Only SIA supports 6-digit account codes. If the last two

digits of the account code are FF, the panel will only use

the first four digits. All other formats will use the first

four digits of the account code.

The call directions that use this account code are System

Maintenance (Troubles, Zone Faults, etc.) and System Test

Transmissions.

NOTE:

SIA will use this account code for Partition 1 and sys-

tem events. System events will be identified by Nri0, with

partition 1 using Nri1.

[311] - Partition 1 Account Code

These account codes are used by the panel when commu-

nicating events for partition 1 when using formats other

than SIA.

NOTE:

The system account codes is 4 digits in length. Valid

entries are 0000-FFFE.

[320] - [358] Reporting Codes

Communicator - Reporting Codes

Unless you are using Automatic Contact ID or Automatic

SIA formats, reporting codes must be programmed in

order for the panel to report events to the central station.

Reporting codes are two digits and can use hexadecimal

digits A through F. To disable a reporting code, program it

as FF (default setting) or 00. For a complete description of

reporting codes which can be programmed and lists of

Automatic Contact ID and SIA format codes, see section

Appendix A: ‘Reporting Codes‘.

[320]-[321] - Alarm Reporting Codes, Zones 1-32

The panel will transmit the Zone Alarm reporting code

for a zone when the zone goes into alarm. 24-hr type

zones will go into alarm whether the panel is armed or

disarmed and report to the central station. All other zone

types will only go into alarm if the panel is armed.

Reporting codes can be one or two digits and can use Hex

digits (A through F). The following is a description of the

different reporting codes that can be programmed and

when the events will be reported to the central station.

[324]-[325] - Alarm Restoral Reporting Codes,

Zones 1-32

If the Restoral on Bell Time-out

Restoral on Bell Time-outRestoral on Bell Time-out

Restoral on Bell Time-out option is selected the

panel will send the Zone Restoral

Zone RestoralZone Restoral

Zone Restoral Reporting Code for the

zone when the alarm output times out AND the zone is

secure. If the zone is not secured when the alarm output

times out the panel will send the restoral immediately

after the zone is secured.

If the Restoral on Bell Time-out

Restoral on Bell Time-outRestoral on Bell Time-out

Restoral on Bell Time-out option is not selected the

panel will immediately send the Zone Restoral reporting

code when the zone is secured or when the panel is dis-

armed, regardless if the alarm output is active or not.

NOTE:

24-hr type zones will report the restoral immedi-

ately after the zone is secured.

[328] - Miscellaneous Alarm Reporting Codes

Duress Alarm:

this reporting code will be transmitted to

the monitoring station whenever a Duress code is used to

perform any function on the system.

Opening After Alarm:

this reporting code will be trans-

mitted to the monitoring station on opening if an alarm

has occurred during the previous armed period.

Recent Closing

: a Recent Closing transmission will be sent

if an alarm occurs within 2 minutes of an exit time expira-

tion. The Recent Closing report will be sent for the first

alarm only.

Zone Expander Supervisory Alarm:

this reporting code is

sent when the system loses communications with any

zone expander module (PC5132 or keypad with on-board

zone).

Zone Expander Supervisory Restoral

: this reporting code

is sent when the system regains communications with all

zone expander modules (PC5132 or keypad with on-

board zone) that have been enrolled on the system.

Cross Zone / Police Code Alarm:

When using Cross Zon-

ing (Section 018, Option 6 ON), this reporting code will be

sent when two Crossed Zones go into alarm during the

cross zone period.

When using Police Code (Section 018, Option 6 OFF), this

reporting code will be sent when any two zones go into

alarm.

If the

Double Hit

option has been enabled, this reporting

code will be sent when two zone alarms occur on the

same zone and the Burglary Verified timer has not

expired.

NOTE:

Only one reporting code will be sent during each

armed to armed period when using Police Code.

Burglary Not Verified

: this reporting code will be sent

after the Burglary Verified Timer expires after a zone

alarm occurs.

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 55 56

Comentarios a estos manuales

Sin comentarios

DSC PC 1555 Manual de instalación Pagina 35

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC PC 1555