DSC PC5020 Manual de instalación descargar pdf (Pagina 28)

Programming Sections: 5.3 Basic Programming PWS Sect 3

Option Definition On/Off Description

7 Telephone Line

Monitor

ON Telephone Line Monitor enabled. The TLM function will be active and the system will indicate a

Trouble #3 condition when using the [*][2] View Trouble Conditions Command.

OFF Telephone Line Monitor disabled. The TLM function will be shut off and telephone line troubles

will not be indicated by the system.

8 Telephone Line

Monitor Audible

Trouble

ON TLM Audible When Armed. When the system is disarmed, a telephone line monitor trouble will

generate a trouble indication as described above. If the system is armed, a telephone line monitor

trouble will generate an audible alarm on the bell or siren for the duration programmed for Bell Tim-

eout or until an access code is entered to disarm.

OFF TLM Trouble Only. A telephone line trouble will generate a trouble indication, the Trouble LED will

come ON, and the keypad sounder will beep until a key is pressed.

[016] - FOURTH SYSTEM OPTION CODES

Option Definition On/Off Description

1 AC Trouble Display ON AC Trouble Displayed. If AC power fails, the condition will be reported to the monitoring station

and will be indicated as a Trouble condition on the system Keypads.

OFF AC Trouble Not Displayed. If AC power fails, the condition will be reported, but the Trouble light

will not be indicated on the system keypads. If [*][2] is entered to view the system troubles, Trouble

#2 will still be displayed.

2 AC Trouble Flash ON Trouble Light Flashes if AC Fails. When AC power is lost from the system, the “Trouble” light will

flash in the base “Ready” and “Armed” mode within 30 seconds from after power is lost. When AC

restores, the “Trouble” light will stop flashing within 30 seconds. If enabled, this option will override

the AC display option.

OFF Trouble Light Does Not Flash on AC Fail.

3 Keypad Blanking ON Blank Keypad When Not Used. If no keys are pressed for 30 seconds, all keypad lights except

backlighting (if enabled) will be shut OFF until the next keypress, Entry delay, Audible Alarm or key-

pad buzzer condition.

NOTE: Keypad function keys will still operate when the keypad is blank, unless the function key is

programmed to require an access code.

OFF Keypad Always Active. The keypad lights will remain ON at all times.

4 Keypad Blanking

Restore

ON Access Code Required to remove Keypad Blanking. A valid access code must be entered before

a blanked Keypad can be used

OFF Access Code Not Required. Pressing any key on a blanked keypad will remove the blanking.

5 Keypad Backlight-

ing

ON Keypad Backlighting is Enabled. All keypads on the system will have backlighting on all of the

time.

OFF Keypad Backlighting is Disabled.

6 Power Save Mode ON Power Save Mode Enabled. If AC power fails, all keypad lights including backlighting will be shut

OFF. The keypad lights will come back ON after a keypress, Entry delay, Audible Alarm or keypad

buzzer condition (except Door Chime). The keypad lights will return to the off state after 30 seconds

of keypad inactivity.

OFF Power Save Mode Disabled.

7 Bypass Status Dis-

play

ON Bypass Status Displayed While Armed. The Bypass status light will be ON if there are zones

bypassed when the system is armed.

OFF Bypass Status Not Displayed While Armed. The Bypass light will be ON only while the system is

disarmed to indicate that there are bypassed zones on the system. When the system is armed, the

Bypass light will be OFF.

NOTE: The Bypass status LED will be ON if there are Stay/Away zones auto bypassed at the time of

arming regardless of whether or not this option is enabled. This option only enables and disables

manual bypass display.

8 Keypad Tampers ON Keypad Tampers are Enabled. All keypads containing Tamper switches will generate Tamper

Alarms and Restores (Sect 338).

OFF Keypad Tampers are Disabled.

NOTE: If this option is used, all keypads should be properly installed and secured (tamper restored)

before enabling the option.

[017] - FIFTH SYSTEM OPTION CODES

Option Definition On/Off Description

1 WLSKey Disarming ON WLS Keys Do Not Use Access Codes. The panel will accept the disarm keycode from an unidenti-

fied Wireless Key, allowing arming/disarming without a code.

NOTE:This option must be enabled when using a PC5132 v2.1 or earlier.

OFF

NOTE: WLS Keys Uses Access Codes. The panel will NOT accept the disarm keycode from an uni-

dentified Wireless Key. An Access code must be associated to a WKEY for proper operation.(Refer to

the PC5132 manual for information on programming wireless keys.)

NOTE: This option must be ON when using a PC5132 older than v3.00.

2 Auto-Arm Schedule

Programming

ON Auto-arm Schedule in [*][6]. The Auto-Arm Schedules (Sect [181] - [188]) are accessible via [*][6]

as well as Installer’s Programming.

OFF Auto-arm Schedule in Installer’s. Programming Only. The Auto-Arm Schedules (Sect [181] -

[188]) are only accessible via Installer’s Programming.

NOTE: This toggle controls access for all eight partitions

WWW.DIYALARMFORUM.COM

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 52 53

Comentarios a estos manuales

Sin comentarios

DSC PC5020 Manual de instalación Pagina 28

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC PC5020