DSC PC5020 Manual de instalación descargar pdf (Pagina 34)

Programming Sections: 5.6 Communicator Programming PWS Sect6

Alarm Canceled: this reporting code will be sent if a valid access

code is entered during the Alarm Cancel window. If a valid access

code is entered during this window, then the Alarm Canceled event

is logged and sent. When the central station has acknowledged this

reporting code/event, a keypad ring-back will occur.

[329] - Priority Alarm and Restoral Reporting Codes

[F], [A], [P] Alarm: this reporting code will be sent if the [F] [A] or [P] key is

used to generate manual alarms.

Auxiliary Input Alarm: this reporting code will be sent when PGM2 is

being used for two wire smoke detectors and the 2-wire smoke detector goes

into alarm.

[F], [A], [P] Restoral: this reporting code will be sent after the [F] [A] [P]

alarm reporting code is sent.

Auxiliary Input Restore: the panel will transmit this reporting code when

the 2-wire smoke detector has restored after an alarm.

[330]-[333] - Tamper Reporting Codes, Zones 1-64

If the panel is programmed for Double EOL zones (See Section 2.10

"Zone Wiring") the panel will report a Zone Tamper Alarm Report-

ing Code if an open condition is present on a zone. A different

reporting code can be programmed for each zone for identification.

[334]-[337] - Tamper Reporting Codes, Zones 1-64

The Zone Tamper Restoral Reporting Code will be transmitted

immediately when the tamper condition is restored.

[338] - Miscellaneous Tamper Reporting Codes

General System Tamper: a General System Tamper Reporting Code

will be transmitted when the tamper zone on any module is violated.

General System Tamper Restoral: the General System Tamper

Restoral Reporting Code will be transmitted when the tamper zone

on the module is restored.

Keypad Lockout: the panel will transmit the Keypad Lockout

Reporting Code if the lockout is activated.

[339]-[340] - Closing (Arming) Reporting Codes, Zones

1-32

The panel will transmit a Closing Reporting Code to indicate a Parti-

tion(s) is armed. A different reporting code can be transmitted for

each User Code, Partition Master Code and System Master Code to

identify who armed the partition(s).

[341] - Miscellaneous Closing (Arming) Reporting

Codes

Closing by Duress Code 33/34: a Closing by Duress Code Report-

ing Code will be transmitted in addition to the Duress reporting code

if a Partition(s) is armed using a Duress Code

Closing by Master or Supervisory Code: the panel will transmit a

Closing Reporting Code to indicate a Partition(s) is armed. A different

reporting code can be transmitted for each User Code, Supervisory

Code and System Master Code to identify who armed the Parti-

tion(s).

Partial Closing: a Partial Closing Reporting Code will be transmitted

if a Partition is armed with zones manually bypassed. The code will

also be transmitted if a Partition Auto Arms with zone(s) in violation.

Special Closing: a Special Closing Reporting Code will be transmit-

ted if the Partition(s) is armed using any of the following methods:

• Quick Arm

• Auto Arm

• Arming via the DLS Software

• Arming via Keyswitch

• 'Away' Function Key Arming

• Arming with the Maintenance Code.

• 'Stay' Function Key arming

Late to Close: a Late to Close Reporting Code will be transmitted if

a partition isn't armed before the auto-arm start time when the late

to close option, (Section 017, option 5) is enabled.

[342]-[343] - Opening (Disarming) Reporting Codes

Access Codes 1-32

The panel will transmit an Opening Reporting Code to indicate

partition(s) is disarmed. A different reporting code can be transmit-

ted for each user code, partition master code and system master

code to identify who armed the partition(s).

[344] - Miscellaneous Opening (Disarming) Reporting

Codes

Opening by Duress Code 33/34: This Reporting Code will be trans-

mitted in addition to the duress reporting code if a Partition(s) is dis-

armed using a Duress Code

Opening by Master or Supervisory Code: The panel will transmit

this reporting code to indicate a Partition(s) is armed. A different report-

ing code can be transmitted for each User Code, Supervisory Code and

System Master Code to identify who armed the Partition(s).

Auto Arm Cancellation: This reporting code is transmitted when the

Auto Arming sequence is canceled or Postponed

Special Opening: A Special Opening Reporting Code will be transmit-

ted if the Partition(s) is disarmed using any of the following methods:

• Disarming using the Maintenance Code

• Disarming via the DLS Software

• Disarming via keyswitch

[345] - Maintenance Alarm Reporting Codes

Battery Trouble Alarm: the panel will transmit a Battery Trouble

Alarm Reporting Code when the backup battery drops below 11.5

DC.

AC Failure Trouble Alarm: the panel will transmit an AC Failure

Trouble Alarm Reporting Code when the AC to the panel is lost and

the AC Failure Communication Delay timer expires.

Bell Circuit Trouble Alarm: a Bell Circuit Trouble Alarm Reporting

Code will be transmitted immediately if an open condition is mea-

sured on the Bell Output of the main panel.

Fire Trouble Alarm: a Fire Trouble Alarm Reporting Code will be

transmitted immediately when an open condition is measured on

any Fire type zone.

Auxiliary Power Supply Trouble Alarm: the Auxiliary Power Sup-

ply Trouble Alarm Reporting Code will be transmitted if the AUX out-

put is shorted.

TLM Trouble: a TLM Trouble Reporting Code can only be transmit-

ted if a LINKS1000/2X50 Communicator is being used (See Section

5.26 "LINKS1000 Cellular Communicator"). The panel will only

transmit the signal after the time programmed for the TLM Trouble

Delay.

General System Trouble: a General System Trouble Reporting Code

will be transmitted if the panel detects any of the following:

• AC Power Failure

• Low Battery

• AUX Output Trouble

• Output #1 on the PC5200/PC5204 Power Supply/Output Module.

General System Supervisory Trouble: a General System Supervi-

sory Trouble Reporting Code will be transmitted if any module goes

missing from the Keybus. If the module is a zone expander the panel

will also transmit the Zone Expander Supervisory Alarm Trouble

Reporting Code.

[346] - Maintenance Alarm Reporting Codes

Battery Trouble Restoral: the Battery Trouble Restoral Reporting

Code will not be transmitted until the battery has been charged over

12.5 V

DC.

AC Failure Trouble Restoral: the AC Failure Trouble Restoral

Reporting Code will be transmitted once AC power has been

restored for the amount of time programmed for AC Failure Com-

munication delays.

Bell Circuit Trouble Restoral: the Bell Circuit Trouble Restoral

Reporting Code will be transmitted as soon as the open condition on

the bell output is corrected.

Fire Trouble Restoral: the Fire Trouble Restoral Reporting Code will

be transmitted when the correct resistance value is measured on any

Fire type zone.

Auxiliary Power Supply Trouble Restoral: the panel constantly

checks the AUX output, when the excessive current draw is removed

the panel will reset the output and transmit an Auxiliary Power Sup-

ply Trouble Restoral Reporting Code.

TLM Restoral: the TLM Restoral Reporting Code will be transmitted

immediately after the trouble is restored.

WWW.DIYALARMFORUM.COM

1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 52 53

Comentarios a estos manuales

Sin comentarios

DSC PC5020 Manual de instalación Pagina 34

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC PC5020