DSC PC5020 Manual de instalación descargar pdf (Pagina 40)

[390]-[393] LINKS Preambles

Downloading can be performed through the LINKS1000 cellular

communicator if the telephone line is disconnected. If using the

LINKS1000 with Call Back, you need to program the LINKS1000 Pre-

amble with the downloading telephone number in order for the

panel to call the computer correctly.

LINKS1000 Cellular Communicator

The LINKS1000 cellular communicator can be used three different

ways: as the sole communicator for the panel, as a back up for either

or both telephone numbers, or as a redundant back up to the land

line communicator (the panel will call both the land line and via the

LINKS1000). A LINKS1000 Preamble is programmable for each tele-

phone number in the event that the land line number is local but the

LINKS1000 is required to dial an exchange. When programming a

LINKS1000 Preamble, all unused digits must be programmed with a

hex decimal “F”.

Sole Communicator

The panel can be programmed to report only using the LINKS1000

cellular communicator when an event occurs. To program this select

only the LINKS1000 for the Communicator Call Direction Options

for the event. In addition the Call LINKS1000 as well as Land Line

option must also be enabled. When the selected event occurs the

panel will only attempt to call central station using the LINKS1000.

NOTE: If a LINKS1000-only event fails to communicate, the

LINKS1000 must successfully communicate a LINKS1000-only event

in order for the FTC trouble to clear.

Backup Communicator

The panel can be programmed to call using the LINKS1000 cellular

communicator if the panel is having difficulty communicating an

event using the land line. To program this select the telephone num-

ber and LINKS1000 options for the Communicator Call Direction

Options for the event. The LINKS1000 is Backup of Land Lines option

must also be selected.

When used as a backup communicator the panel will attempt to call

the central station in the following manner:

• the panel will try to call using land lines - if unsuccessful the

panel will try to call using the LINKS1000

• if unsuccessful the panel will try to call using the land lines

• if unsuccessful the panel will try to call using the LINKS1000

This process will continue until the panel has successfully communi-

cated with the central station or the Maximum Dialing Attempts

has been reached.

[382] - THIRD COMMUNICATOR OPTION CODES

Option Communicator Code On/Off Description

1 Contact I.D. Partial Closing

Identifier

ON Partial Closing Identifier = 5. Contact I.D. uses ‘5’ as the Identifier for the Partial Closing

event.

OFF Partial Closing Identifier = 4. Contact I.D. uses ‘4’ as the Identifier for the Partial Closing

event. This option is defaulted OFF.

2 Walk Test Communication ON Zone Alarms Communicate during Walk Test Enabled. Zone alarms that occur during Walk

Test will communicate if programmed to do so.

OFF Zone Alarms Communicate during Walk Test Disabled. Zone alarms that occur during Walk

Test will not communicate even if programmed.This option is defaulted OFF.

3 Communications Cancelled

Message

ON Communications Cancelled Message Enabled. The “Communications Cancelled”

(LCD5500Z) or “CC” (LCD5501Z) message will be displayed if alarms are acknowledged during

the Transmission Delay time. This message will be displayed for 5 seconds on all keypads on the

partition. The acknowledgment can be from an access code, disarm function key, or a keyswitch

zone. Caution: This option must NOT be turned OFF for SIA-FAR installations.

OFF Communications Cancelled Message Disabled. The “Communications Cancelled” message

will not be displayed. This option is defaulted OFF.

4 Call Waiting Cancel ON Call Waiting Cancel Enabled. The Call Waiting dialing string programmed in Section [304] will

be dialed before the first attempt of each phone number. All subsequent dialing attempts to the

same phone number will not use the Call Waiting Cancel dialing string.

OFF Call Waiting Cancel Disabled. The Call Waiting dialing string will not be dialed. This option is

defaulted OFF. Note: A call waiting cancel on a non-call waiting line will prevent successful

connection to the central station.

6 AC Failure Transmission

Delay

ON AC Failure Transmission Delay. Delay is in Hours.

OFF AC Failure Transmission Delay. Delay is in Minutes.

7-8 ON Reserved For Future Use

WWW.DIYALARMFORUM.COM

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 52 53

Comentarios a estos manuales

Sin comentarios

DSC PC5020 Manual de instalación Pagina 40

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC PC5020