DSC PC5020 Manual de instalación descargar pdf (Pagina 44)

Programming Sections: 5.10 Module Programming PWS Sect 10

[703] - Delay Between Dialing Attempts

For standard (force) dialing, the panel will go off-hook, search for

dialtone for 5 seconds, hang-up for 20 seconds, go off-hook, search

for dialtone for 5 seconds, then dial. If there is no initial handshake

recognized within 40 seconds, the panel will hang up. This program-

mable timer adds a delay before the next call is attempted, and is

defaulted to 001 for a total of six seconds.

5.10 Module Programming PWS Sect 10

The programming sections listed below pertain to additional mod-

ules on the system. For instructions on programming these modules

and a description of each programming section, see the associated

installation manuals.

1. PC5400 Programming Section [801]

2. PC5936 Programming Section [802]

• PC5936 Audio Interface will allow you to connect to 16 Interior

(PC5921) or exterior (PC5921EXT) Intercom Station. These sur-

face mounted stations contain a speaker and a microphone. This

module enables Page/Answer, Do Not Disturb, Baby Monitor,

Answer Incoming Calls, Doorbell Function, and Background

Music features in your alarm. This module also has the Listen-in

feature for central station monitoring. The central station can

select the audio station, listen/talk, extend on-line time and hang

up. The Listen-In feature can be enabled separately for telephone

numbers 1/3 and 2.

All Talk/Listen and/or video sessions will be

disconnected if the panel needs to communicate alarms to the

central station.

• Alternate Communicator Programming Section [803]

• PC5132 Programming Section [804]

• PC5100 Programming Section [805]

• PC5108L Programming Section [806

NOTE: All talk/listen and/or video sessions are disconnected when

the panel communicates alarms to the central station.

NOTE: Option [5] in Section [382] must be enabled to access this

section.

Telephone 1 & 3 Listen-In Enabled . . . . . . .Section [381], Option 5

Telephone 2 Listen-In Enabled. . . . . . . . . . .Section [381], Option 6

5 Access Code Length ON 6-digit Access Codes. All access codes on the system will be 6 digits in length except the Panel

I.D. Code and the Downloading Access Code.

• System Master Code = XXXX56 XXXX = previous code, (1234)

• Installer Code = YYYY55 YYYY = previous code, (5555)

OFF 4-digit Access Codes. All access codes on the system will be 4 digits in length. For any existing

codes, the last 2 digits are removed.

6 Busy Tone ON Busy Tone Detection Enabled. If these tones are detected, the communicator will disengage

the phone line and try to place the call again following the “Delay Between Dialing Attempts”

OFF Busy Tone Detection Disabled. The communicator will use the standard dialing procedure for

every attempt.

7 Battery Current Charge ON High Current Battery Charge. Approximately 650-700 mA.

OFF Standard Current Battery Charge. At approximately 350 mA.

8 ON For Future Use

[701] FIRST INTERNATIONAL OPTION CODES

Option International Code On/Off Description

[702] SECOND INTERNATIONAL OPTION CODES

Option International Code On/Off Description

1 Pulse Dial ON Pulse Dialing Make/Break Ratio is 33/67

OFF Pulse Dialing Make/Break Ratio is 40/60

2 Force Dial ON Force Dialing Enabled. If the first attempt by the panel to call the monitoring station fails to

detect a dialtone, on every subsequent attempt the panel will dial regardless of the presence of

dialtone. See {703] Delay Between Dialing Attempts

OFF Force Dialing Disabled. The panel will not dial the programmed telephone number if dialtone

is not present.

3 Land Line Test Transmission ON Land Line Test Transmission Interval is in Minutes. The value programmed in Section [370]

Seventh entry is in Minutes.

OFF Land Line Test Transmission Interval is in Days. The value programmed in Section [370] Sev-

enth entry is in Days. NOTE: This option must be OFF for the PC5020CF.

4 Handshake ON 1600 Hz Handshake. The communicator responds to a 1600 Hz handshake for BPS formats.

OFF Standard Handshake. The communicator responds to the handshake designated by the for-

mat selected (1400 or 2300 Hz).

5 I.D. Tone ON I.D. Tone Enabled. After the telephone number is dialed, the panel will emit a tone (as speci-

fied by Option 6) for 500 ms every two seconds to indicate that it is a digital equipment call, not

voice.

OFF I.D. Tone Disabled.

6 I.D. Tone Frequency ON 2100 Hz I.D. Tone

OFF 1300 Hz I.D. Tone

7 DLS Window ON One Time 1-hour user Enabled DLS Window. The User Enabled DLS Window is 1 hour in

length and will be closed after a successful hang-up from a downloading call.

OFF Full 6-hour User Enabled DLS Window. The User Enabled DLS Window is 6 hours in length

and remains open after a successful hang-up from a downloading call. This option determines

the length of the DLS window available on power up.

8 FTC Bell ON Bell on FTC when armed. If a Failure to Communicate Trouble is generated while the system is

armed, the Bell output will sound for the length of Bell time-out or until the system is disarmed.

OFF FTC Trouble only when armed. If a Failure to Communicate Trouble is generated while the

panel is armed, the Bell output will not sound but the keypad buzzer will sound trouble beeps

until a key is pressed.

WWW.DIYALARMFORUM.COM

1 2 ... 39 40 41 42 43 44 45 46 47 48 49 ... 52 53

Comentarios a estos manuales

Sin comentarios

DSC PC5020 Manual de instalación Pagina 44

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC PC5020