DSC PC6010 Manual de instalación descargar pdf (Pagina 16)

SET CYCLE DAYSSET CYCLE DAYS

SET CYCLE DAYS

(0)(0)

(0)

SET 24HR TIMESET 24HR TIME

SET 24HR TIME

(1)(1)

(1)

Auto Contact ID?

YES = If the Auto Contact ID option is enabled, the panel will operate as follows: If an event’s reporting

code is programmed as [00], the panel will not attempt to call the central station. If the reporting

code for an event is programmed as anything from [01] to [FF], the panel will automatically generate

the zone or access code number. See Appendix B for a list of the codes which will be transmitted.

The panel will automatically generate all zone and access code numbers, eliminating the need to

program these items.

NO = The panel will operate as follows: If an event’s reporting code is programmed as [00] or [FF], the

panel will not attempt to call central station. If the reporting code for an event is programmed as

anything from [01] to [FE], the panel will send the programmed reporting code.

Communicator Miscellaneous

Program other options relating to the communications of the panel.

Program the number of dialing attempts from 000 to 255 that the panel will make before a Failure To

Communicate (FTC) trouble occurs for telephone number one. The default number of attempts is 010.

NOTE: Do not program this section with 000.

Program the number of dialing attempts from 000 to 255 that the panel will make before a Failure To

Communicate (FTC) trouble occurs for telephone number two. The default number of attempts is 010.

NOTE: Do not program this section with 000.

Program the number of dialing attempts from 000 to 255 that the panel will make before a Failure To

Communicate (FTC) trouble occurs for telephone number three. The default number of attempts is 010.

NOTE: Do not program this section with 000.

Enter the time in minutes, that an AC trouble on the main panel must be present, before the AC trouble

reporting code will be logged or communicated. Valid entries are from 000 to 255. The default setting is

060.

Enter the time in seconds that the panel will delay the communication of a zone alarm. Valid entries are

from 000 to 255. The default setting is 000. If the panel is disarmed within the programmed time, no alarm

communication will be sent. See “TX DELAY?” under zone toggle options to enable the transmission delay

on each zone.

Test Code Transmission

Test Code Transmission. To have the panel send test transmissions, you must program the time of day, the

number of days between test transmissions and the test transmission reporting code. You must also enable

the “PERIODIC TX?” communications toggle option.

Enter the number of days between test code communications. Valid entries are from 001 to 255. The

default setting is 030.

Enter the time of day the panel will send the test code. Program the time in 24-hour format HH:MM. The

default setting is 0000.

AC FAIL TX DELAYAC FAIL TX DELAY

AC FAIL TX DELAY

(3)(3)

(3)

MAX. ATTEMPTS 3MAX. ATTEMPTS 3

MAX. ATTEMPTS 3

(2)(2)

(2)

ZONE TX DELAYZONE TX DELAY

ZONE TX DELAY

(4)(4)

(4)

TEST CODE TXTEST CODE TX

TEST CODE TX

(5)(5)

(5)

COMMS MISCCOMMS MISC

COMMS MISC

(2)(2)

(2)

MAX. ATTEMPTS 2MAX. ATTEMPTS 2

MAX. ATTEMPTS 2

(1)(1)

(1)

MAX. ATTEMPTS 1MAX. ATTEMPTS 1

MAX. ATTEMPTS 1

(0)(0)

(0)

AUTO CONTACT IDAUTO CONTACT ID

AUTO CONTACT ID

SYSTEM AREASYSTEM AREA

SYSTEM AREA

COMMUNICATORCOMMUNICATOR

COMMUNICATOR

COMMS MISC COMMS MISC

COMMS MISC

TEST CODE TXTEST CODE TX

TEST CODE TX

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 51 52

Comentarios a estos manuales

Sin comentarios

DSC PC6010 Manual de instalación Pagina 16

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC PC6010