DSC PC6010 Manual de instalación descargar pdf (Pagina 40)

AREA SECTIONAREA SECTION

AREA SECTION

ADAD

D/D/

EDIT AREA EDIT AREA

EDIT AREA

AREA TIMESAREA TIMES

AREA TIMES

Area Times

The following programming sections are for programming various times separately for each area.

The keypads will give a tone to signal an entry delay when a Standard Delay or Force Arm Delay zone is

activated. This gives the user time to disarm the system when they enter through a door. The entry delay

time is programmable from 000 to 255 seconds (see “Zone Types” under the “Area Section”). The

default setting is 030.

When a system is armed, the zones will not become active until the exit delay has expired, this gives the

user time to exit the building without tripping alarms. The exit delay time is programmable from 000 to

255 seconds. The time remaining will be displayed on the keypad. The default setting is 120.

This entry time is for Auxiliary Delay zones, for doorways that may need a longer entry delay than standard

delay zones. This time is programmable from 000 to 255 seconds (see “Zone Types” under the “Area

Section”). Only the standard exit delay time will be displayed on the keypad countdown. The Auxiliary Exit

Delay will not be displayed. The default setting is 045.

This exit time is for auxiliary delay zones, for doorways that may need a longer exit delay than standard

delay zones. This time is programmable from 000 to 255 seconds (see “Zone Types” under the “Area

Section”). The default setting is 120.

NOTE: The auxiliary entry/exit delays should not be shorter than the standard entry/exit delay times.

This is the maximum amount of time between alarms that will allow the Conditional Alarm output to

activate. Programmable from 000-255. The default is 010 minutes.

The AutoArm Prealert time is programmable by area from 000-255. The default is 001 minute.

If the selected area is a high-security area (e.g. an internal vault or cash machine room), you may want to

program the system to automatically re-arm the area after it has been disarmed. If you program a time

other than 000 in this section, the system will automatically re-arm the area when that time expires. Valid

entries are from 001 to 255 minutes. Program 000 if the area will not be automatically re-armed. The

system will sound an auto-arm pre-alert according to the AutoArm PreWarn time described above.

Once a user enters the area, if they enter their code again, or have access granted from the system again,

the system will reset the Auto Re-arm timer. If a user arms the area using a code or an access card, the

area will arm immediately, without an exit delay.

NOTE: If you program an area for Auto Re-arm, you must assign at least one keypad to the area.

AREA TIMESAREA TIMES

AREA TIMES

(2)(2)

(2)

ENTRY DELAYENTRY DELAY

ENTRY DELAY

(0)(0)

(0)

EXIT DELAYEXIT DELAY

EXIT DELAY

(1)(1)

(1)

AUX ENTRY DELAYAUX ENTRY DELAY

AUX ENTRY DELAY

(2)(2)

(2)

AUX EXIT DELAYAUX EXIT DELAY

AUX EXIT DELAY

(3)(3)

(3)

AUTOARM PRE-WARNAUTOARM PRE-WARN

AUTOARM PRE-WARN

(5)(5)

(5)

CONDITIONAL ALRMCONDITIONAL ALRM

CONDITIONAL ALRM

(4)(4)

(4)

AUTO RE-ARMAUTO RE-ARM

AUTO RE-ARM

(6)(6)

(6)

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 51 52

Comentarios a estos manuales

Sin comentarios

DSC PC6010 Manual de instalación Pagina 40

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad DSC PC6010